Browse our common questions section for answers to questions about our products, installation, service, maintenance, and more.

Maintenance

No. The louvers allow room air to move around the heat exchanger. Blocking this air flow can cause fires and will void your manufacturer's warranty and possibly your homeowner's warranty.

No. The frequency of the remote control cannot be changed without special equipment, which is not readily available to homeowners and/or service companies. Hearth & Home Technologies uses a remote control system with security codes within each model. These security codes are burned into the transmitter of each model and cannot be changed. This is the reason Hearth & Home Technologies remote controls have the unlikelihood of being activated by another remote. If there is more than one Hearth & Home Technologies remote control at a home it is important that each hand-held transmitter has had the “learn” function activated to its designated receiver. If one hand-held transmitter was used in the “learn” activation for both receivers only one hand-held will function.

On new wood-burning fireplaces, first determine what you are burning. You should only be using seasoned wood, newspaper, or kindling. Firestarters can cause a smell. Seasoned fireplaces: what have you burned in the past? Have you cleaned the fireplace prior to burning? If you have used firestarters and/or prefabricated logs, these products are bound together with a wax-type substance, which does not dissipate. This wax can pool and has been found under the hearth refractory and can cause a very foul odor. Also check what is on top of the fireplace. Remove all objects from mantel to see if this eliminates the smell.

Hearth & Home Technologies’ remote controls work by radio frequency, which offers the unlikelihood of another remote control activating your individual gas fireplace product.

Infrared (light signals) is often used with television and stereo remotes and requires there be no interference between the hand-held and the receiver. Fireplace facings, louvers and different installation options make infrared an unreliable option for fireplaces. Also, the brightness of the flame interferes with infrared control systems.

Sonic or Sound is the third technology used with remote controls. The early sonic technology was used on television, but quickly abandoned due to limitation in channels and choices. Most Sonic technology is used in the pest control industry today.

The majority of our gas fireplaces and inserts are direct vent (DV). This means they have a fixed glass front which seals the gas burner and combustion firebox off from your home. 100% of the combustion air used by the fireplace comes from outside the home through a coaxial pipe. A smaller pipe inside the larger pipe eliminates all combustible gases, maintaining indoor air quality. The vent can be run horizontally through an outside wall, or vertically through the roof, depending on your preference.

It is very important to clean your glass after the initial 3 hours of burn time. Failure to do so can cause permanent etching of your glass.

  1. Make sure your glass is completely cooled. It is also recommended to turn the gas off when servicing your appliance.
  2. Remove the front face or louvers of your fireplace; carefully remove the glass assembly of your fireplace (following the instructions in your manual) and lay it on a soft surface.
  3. Wipe both sides with household glass cleaner (do not use a product with ammonia), using a soft cloth.
  4. For heavy deposits, use Stove Bright Glass Cleaner , Rutland White Off Glass Cleaner, or other hard water deposit glass cleaner recommended by your servicing dealer.
  5. Carefully replace glass on front of fireplace (following the instructions in your manual), making sure glass assembly and front are secured.
  6. After this initial cleaning, clean your glass as often as necessary, particularly if adding new ember material. Never use any abrasive cleaners or cloths to clean your glass. Scratching can cause the glass to shatter.

CAUTION: ALWAYS REMOVE YOUR FIREPLACE GLASS PRIOR TO LIGHTING YOUR PILOT

STEP 1: Locate gas supply valve (typically behind louvers, below glass opening - may be red or blue).

STEP 2: Open valve by pivoting handle to be parallel to gas line.

STEP 3: Locate pilot assembly with spark igniter (located behind and below logs in the firebox - typically in the bottom center).

STEP 4: Then locate red or black igniter button.* Push igniter to verify spark at pilot area.

STEP 5: Locate the black or green valve control knob (knob with the words "ON", "OFF" and "PILOT" on it). Push in and rotate counter-clockwise until the word "pilot" is in the 6 o'clock position.**

STEP 6: While pressing and holding in the valve knob (in "PILOT" position - it should press in about 1/4"), press the red piezo button repeatedly (once per second) until the pilot ignites. If the pilot does not light, wait 5 minutes and try again. Once the pilot is lit, continue to hold the valve knob in for 30 seconds, then slowly release.

STEP 7: If the pilot light goes out, contact your nearest dealer for service. Remember to shut the gas supply valve off (picture #1). If it remains lit, press the valve knob in slightly and rotate counter-clockwise until the word "ON" is in the 6 o'clock position.

STEP 8: Finally, turn the unit's ON/OFF switch (or wall switch or remote control) to the "ON" position to start your fire. Make sure you put the glass front back on the fireplace prior to burning your fireplace. Make sure the glass is securely clamped on, at all points, prior to replacing the front.

STEP 9: Enjoy your fireplace!

* If you do not see a red or black spark igniter button, you do not have a manual ignition system. If power is actively supplied to your fireplace, simply turn the on/off button, wall switch or remote control to "on" to ignite your main burner.

** Note: Some valve assemblies may be inverted in their brackets. If yours appears to be the mirror image of picture #4, then the word "PILOT" will be in the 12 o'clock position to light the pilot, and "ON" will be set to the 12 o'clock position to turn on your main burner.

CAUTION: ALWAYS REMOVE YOUR FIREPLACE GLASS PRIOR TO LIGHTING YOUR PILOT

Please refer to the installation manual or users guide for your fireplace to see how the glass is attached to your specific model and instructions for removal.

Under normal operating conditions the batteries should last 6 – 12 months. Each of the batteries used in the hand-held transmitters should be producing 1.5V to 1.6V to operate. If the batteries are generating 1.3V to 1.35V or less the batteries should be replaced and can cause intermittent operation.

Your fan kit has a rheostat control (like a light dimmer). You can get more air from your fan by making sure the fan control is turned up to the desired level. The fan control can be found in the control area behind the lower louver of the fireplace, or on a wall switch with rheostat. We also provide optional remote controls which can control your fan speed from your favorite chair! Your dealer can help you with adding a remote control.

Our fans are purposely designed at lower CFMs (cubic feet per minute). There are two reasons for this. This first is to minimize fan noise. Second, a high velocity would tend to cool the air temperature coming out of the top louver of the fireplace. The fan is designed to move warm air into the room, not to move air clear across the room.

On gas fireplaces that are not brand new and are emitting some odor, try cleaning behind the upper and lower louvers. Dust can cause odor. Another source of odor can be the items you have on your mantel. Remove all objects from your mantel and then replace the objects one at a time. A third source of odor can be from the adhesives used in surround materials. This will need to be investigated by your installer. If these suggested sources don’t correctly identify the odor, contact your dealer where the fireplace was purchased and have your fireplace inspected.

Our fan kits come with a rheostat control (like a light dimmer). You can turn the control down to reduce the air noise from your fan. The fan control can be found in the control area behind the lower louver of the fireplace. We also provide optional remote controls which can control your fan speed and flame height from your favorite chair! Your dealer can help you with adding a remote control.

Please see the detailed instructions below. In addition, your local dealer can provide the proper equipment and resources to assist you with this.
Instructions for battery replacement and remote programming
Find a Dealer

Yes. We recommend annual service of your fireplace by a qualified serviceperson. This will ensure that your appliance is functioning properly.

If your system is controlled from an IntelliSwitch wall control, the batteries may be left in the unit. If not, install the batteries only when there is a power outage.

1) A hand-held transmitter. This is like a TV remote with which a person operates various features of the fireplace.
2) A receiver. This is located inside or near the fireplace and receives the radio frequency from the hand-held transmitter.
3) A Solenoid (for remote model RCT-MLT). This provides the option of a remote controlled variable flame. The solenoid is installed onto the regulator (located on the gas valve) of the fireplace to vary the gas pressure to the burner.

Excessive metal will deflect radio frequency in a direction that may not be in line with the receiver of your remote control. Interference of your radio frequency can cause the remote control to not respond properly to the hand-held transmitter. Hearth & Home Technologies has many built in safety functions to ensure that your remote control and fireplace operate in harmony. For this reason the receiver of the remote should not be installed to the very back of the fireplace. Large metal artwork can interfere with radio frequency.

Both the transmitter and receiver in model SMART-BATT are powered by batteries. Models SMART-STAT, RCT-MLT, RC-100, RC-200, and RC-300 are powered by batteries in the hand-held transmitters. The receiver is plugged into the junction box located in the bottom of the fireplace (Note: this requires an electrical hookup by qualified electrician at time of fireplace installation).

Your local dealer can provide the proper diagnosis, equipment and resources to provide the necessary corrective actions. We ask that your dealer contact us if further assistance is needed to resolve your service issue. Find a Dealer

There are several possible causes of feeling cold air from a wood fireplace. You will want to make sure the damper is closed. Also check the installation manual for any other potential openings that may need to be shut. If the fireplace is mounted on cement versus plywood, that can also transfer cold into your home. If the chase area or doghouse is not insulated adequately, that is another possibility. Please check with your builder or installer on the insulation of the chase.

Installation

You can if you have a heat circulating model, which means there are louvers in the top and bottom facing of the fireplace, and if there is electrical power to the junction box behind the lower louver, then you can easily install a fan kit.

No. Doing so will void the warranty on your fireplace and possibly void your homeowners insurance. An unvented gas log set that complies with the ANSI Z21.60 standard as a vented gas log set can be used as long as the damper is removed from the unit, but any other type of unvented log set will cause hazardous conditions.

No. The louvers allow room air to move around the heat exchanger. Blocking this air flow can cause fires and will void your manufacturer's warranty and possibly your homeowner's warranty.

Yes! However, there is an operational priority (Pecking order) of the various ways to turn your fireplace ON or OFF. The highest priority goes to the ON/OFF switch located near the valve assembly. For example, if you have the fireplace is turned “ON” via this switch, it will negate the wall switch and ON/OFF feature of your remote control.

Next, the wall switch takes priority over the remote control. In other words, if the wall switch is in the “ON” position and the units switch is in the “OFF” position, the remote control will not be able to turn the fireplace on or off. In either case, the RCT-MLT functions will work unless the "on- off" feature of the wall switch or fireplace switch is in the “ON” position.

Many of our gas fireplace models that have louvers or grills on the front can have a fan kit added. You will want to make sure that electricity is run to the junction box underneath the fireplace first, before ordering & installing a fan kit. You can test the junction box by plugging a lamp into the junction box and switching it on and off. Also make sure the circuit breaker is not tripped. If there is no electricity to the junction box you would have to run electric to the fireplace first before the fan kit could be installed. You can order a fan kit through your local dealer; installation instructions are packed with it.

Installation of our hearth products must be done in strict accordance with local or national building codes, and the unit's installation manual. We recommend that our products be installed by a factory-trained professional. You can find a factory-trained professional on this website under the Dealer Locator section.

You need to check with the manufacturer of your television. We follow the recommendations of the TV manufacturer. NOTE: we take no responsibility of any damage caused by the heat of the fireplace.

No. We make a wide variety of products that can be used in an outdoor porch, patio or open area under the Outdoor Lifestyles product line. You can view these products on this website under Outdoor Products.

No. The Manufacturer’s Suggested Retail Price (MSRP) shown on the website includes the fireplace or appliance only. Fronts, piping, surrounds, gas or electric connections, and installation will be in addition to this suggested price.

Please refer to the installation manual or users guide for your fireplace to see how the glass is attached to your specific model and instructions for removal.

The FCC in the United States and IC in Canada regulate the distance in which a radio frequency from the hand-held transmitter can operate. In optimum conditions, this distance is 90 feet. Since there are many things than interfere with radio frequency the maximum realistic distance from which a hand-held transmitter will communicate with the receiver is 25 feet. Radio frequency will go through normal residential constructed walls (wood, plaster, drywall), but distance will be reduced traveling through walls.

Yes. We recommend annual service of your fireplace by a qualified serviceperson. This will ensure that your appliance is functioning properly.

1) A hand-held transmitter. This is like a TV remote with which a person operates various features of the fireplace.
2) A receiver. This is located inside or near the fireplace and receives the radio frequency from the hand-held transmitter.
3) A Solenoid (for remote model RCT-MLT). This provides the option of a remote controlled variable flame. The solenoid is installed onto the regulator (located on the gas valve) of the fireplace to vary the gas pressure to the burner.

Excessive metal will deflect radio frequency in a direction that may not be in line with the receiver of your remote control. Interference of your radio frequency can cause the remote control to not respond properly to the hand-held transmitter. Hearth & Home Technologies has many built in safety functions to ensure that your remote control and fireplace operate in harmony. For this reason the receiver of the remote should not be installed to the very back of the fireplace. Large metal artwork can interfere with radio frequency.

Both the transmitter and receiver in model SMART-BATT are powered by batteries. Models SMART-STAT, RCT-MLT, RC-100, RC-200, and RC-300 are powered by batteries in the hand-held transmitters. The receiver is plugged into the junction box located in the bottom of the fireplace (Note: this requires an electrical hookup by qualified electrician at time of fireplace installation).

There are several possible causes of feeling cold air from a wood fireplace. You will want to make sure the damper is closed. Also check the installation manual for any other potential openings that may need to be shut. If the fireplace is mounted on cement versus plywood, that can also transfer cold into your home. If the chase area or doghouse is not insulated adequately, that is another possibility. Please check with your builder or installer on the insulation of the chase.

Purchase

Not directly. We only sell fireplaces through our local dealers. You can find a dealer near you by clicking on the Dealer Locator tab and entering your zip code, state or province in the box provided.

In an effort to deliver quality products, service, and safety, Hearth & Home Technologies, Inc. distributes our family of products exclusively through authorized and trained distributors and dealers. Occasionally, individuals will attempt to sell products online without the consent of the manufacturer. Heatilator, Heat & Glo, Harman and Quadra-Fire do not authorize the sale of products online. Here are a few things to consider if you are contemplating an online purchase of a quality hearth product.

Warranty - Heatilator, Heat & Glo, Harman or Quadra-Fire does not warranty products sold outside of our authorized dealer network, nor will they warranty service work on the product that is performed by anyone other than an authorized dealer. In addition, the warranty on our products applies to the original owner only and is nontransferable.

Customer Expectations - Our dealers are trained to evaluate your specific needs and suggest to you the products that will best meet those needs. When buying products online, you may be purchasing products that are not ideal for your situation and, as a result, be more costly than you anticipated. The products also require specific venting components with restrictions as to their installation which may not be evident in the purchase without a trained dealer to assess the installation application and recommend the appropriate venting scheme.

Shipping Damage - Our products are designed to ship to our customers using approved carriers and processes. The risk for damage increases if you attempt to ship product outside of our dealer network. We will not be responsible for any costs related to shipping damage.

Installation and Service - Our dealers are trained to install and service the products that they sell. We strongly recommend our products be installed and serviced by authorized dealers. Your warranty will be void if the product is not installed, operated and maintained in compliance with local building codes and with the instructions in the installer’s guide, owner’s guide and listing agent identification label furnished with the product. Your warranty will also be void if any service work is performed on the product by anyone other than an authorized representative. Furthermore, many local dealers will not service a fireplace they did not sell, making the authorized service of your product much more expensive. Lastly, the installation and set up of a product requires very specific installation and operational accessories. These accessories are often times not included in online sales, and can be very difficult and expensive to find after the fact.

For proper sales and service, find a local authorized dealer near you.

Yes! However, there is an operational priority (Pecking order) of the various ways to turn your fireplace ON or OFF. The highest priority goes to the ON/OFF switch located near the valve assembly. For example, if you have the fireplace is turned “ON” via this switch, it will negate the wall switch and ON/OFF feature of your remote control.

Next, the wall switch takes priority over the remote control. In other words, if the wall switch is in the “ON” position and the units switch is in the “OFF” position, the remote control will not be able to turn the fireplace on or off. In either case, the RCT-MLT functions will work unless the "on- off" feature of the wall switch or fireplace switch is in the “ON” position.

Not on a direct vent or B vent model. A gas fireplace is an engineered system that includes the firebox, burner, logs, venting and options which are tested and listed by AGA or UL. Changing any of the specifications or placement of the logs could void your manufacturer's warranty, and possibly even your homeowner's warranty.

The FCC in the United States and IC in Canada regulate the distance in which a radio frequency from the hand-held transmitter can operate. In optimum conditions, this distance is 90 feet. Since there are many things than interfere with radio frequency the maximum realistic distance from which a hand-held transmitter will communicate with the receiver is 25 feet. Radio frequency will go through normal residential constructed walls (wood, plaster, drywall), but distance will be reduced traveling through walls.

Under normal operating conditions the batteries should last 6 – 12 months. Each of the batteries used in the hand-held transmitters should be producing 1.5V to 1.6V to operate. If the batteries are generating 1.3V to 1.35V or less the batteries should be replaced and can cause intermittent operation.

1) A hand-held transmitter. This is like a TV remote with which a person operates various features of the fireplace.
2) A receiver. This is located inside or near the fireplace and receives the radio frequency from the hand-held transmitter.
3) A Solenoid (for remote model RCT-MLT). This provides the option of a remote controlled variable flame. The solenoid is installed onto the regulator (located on the gas valve) of the fireplace to vary the gas pressure to the burner.

Excessive metal will deflect radio frequency in a direction that may not be in line with the receiver of your remote control. Interference of your radio frequency can cause the remote control to not respond properly to the hand-held transmitter. Hearth & Home Technologies has many built in safety functions to ensure that your remote control and fireplace operate in harmony. For this reason the receiver of the remote should not be installed to the very back of the fireplace. Large metal artwork can interfere with radio frequency.

Both the transmitter and receiver in model SMART-BATT are powered by batteries. Models SMART-STAT, RCT-MLT, RC-100, RC-200, and RC-300 are powered by batteries in the hand-held transmitters. The receiver is plugged into the junction box located in the bottom of the fireplace (Note: this requires an electrical hookup by qualified electrician at time of fireplace installation).

Hearth & Home Technologies offers several remote options with different features and functions to fit the different needs of today homeowners. They are all compact in size to fit the palm of your hand and come with a wall mounting bracket for easy storage.

SMART-BATT - This remote is perfect for you if your fireplace was previous installed without power and it would be too costly or impossible to wire electricity to it. This remote offers the feature of turning the flame on and off manually or by thermostatic temperature control. Count down timer system (15 min to 9 hours). 24 hour clock. Low battery indicator icon. Safety Feature: child proof setting to disable the on/off button and manual shutdown after 9 hours of continuous operation.

SMART-STAT –120 volts must be wired to the fireplace. This remote is ideal for the homeowner who wants the functions of a wall thermostat and the convenience of a remote control. Use manual or thermostatic settings to operate the fireplace at desired temperature between 45 to 99 degrees. Count down timer system (15 min to 9 hours). 24 hour clock. Low battery indicator icon. Safety Features: A child proof setting to disable the on/off button is also standard and manual shutdown after 9 hours of continuous operation.

RCT-MLT – If you enjoy having the best, then this remote is ideally suited for you. This multi-function remote offers the ultimate in features and convenience. It can conveniently do the following with just the touch of a button:
- Turns the flame on and off manually.
- Functions as a remote thermostat.
- Has an automatic timer function that allows you to turn the fireplace on for a desired amount of time between 1 to 90 minutes.
- Easily adjusts your fan setting (High, Medium, Low).
- An LED/LCD digital read out of the room’s temperature.
- Safety features; If the fireplace is turned on manually or by the thermostat and is on constantly for 9 hours the remote will turn the fireplace off.
- Child Proof setting to disable the on/off button is also standard.

Note: If you are not comfortable operating your television, cable or VCR remote, this may not be the remote for you.

Remote Controls are a consumer convenience. They are great for the busy lifestyles of today and will enhance the relaxing mood created by our gas fireplace by allowing the user to relax in their favorite chair and operate their fireplace while reclining in comfort. They are especially convenient in large rooms where a switch on the fireplace or on the wall is not always easily accessed. It is also an extremely popular option for bed/bath sitting rooms.

Operation

No. Doing so will void the warranty on your fireplace and possibly void your homeowners insurance. An unvented gas log set that complies with the ANSI Z21.60 standard as a vented gas log set can be used as long as the damper is removed from the unit, but any other type of unvented log set will cause hazardous conditions.

No. The louvers allow room air to move around the heat exchanger. Blocking this air flow can cause fires and will void your manufacturer's warranty and possibly your homeowner's warranty.

No. The damper must be in the fully open position when using a wood-burning fireplace. Partially closing the flue (chimney) damper can cause smoke to spill into the room when burning wood, or cause carbon monoxide (CO) to come into the room when using gas logs.

Not on a direct vent or B vent model. A gas fireplace is an engineered system that includes the firebox, burner, logs, venting and options which are tested and listed by AGA or UL. Changing any of the specifications or placement of the logs could void your manufacturer's warranty, and possibly even your homeowner's warranty.

Not if your fireplace was shipped with a glass panel on the front. Direct vent fireplaces are sealed combustion systems and need the glass on to function properly. We sell optional screen mesh panels that go on the front of the glass that takes away any reflection, and adds an additional safety barrier against accidental contact with the hot glass panel. The other type of gas fireplaces we sell, called B-vent fireplaces, come with fixed, not sealed, glass fronts. You would need to check with your local dealer in the area to determine if the glass panel can be removed from this type of unit. Because removal of the glass is totally dependent on the specific unit installed, we cannot recommend that the glass be removed unless the specific model of unit denotes that it can be removed and the fireplace will still operate safely.

It's not recommended in climates that are high in humidity. Otherwise, you can turn the pilot off when you won’t be using your appliance for an extended period of time, and then use our on-line instructions to relight the pilot when needed.

Hearth & Home Technologies remote controls have a manual switch on the receiver that can be turned to the OFF position. This switch is manual and will break the contact with the power source, whether it is battery or 120V power. This switch is just like the main power switch that controls any electrical appliance. It is completely unnecessary to unplug or remove batteries from the receiver.

Taking the batteries out of the hand held transmitter will not guarantee against accidental activation. Remember that each remote is equipped with a safety feature, which turns the fireplace off after 9 hours of continuous usage, when operated in the “manual mode”.

Operating the fireplace for longer than a continuous 9 hours is not a safety issue, but can cause the temperature in the room of the fireplace to reach higher than normal temperatures. It is always required to maintain the necessary clearance to combustibles as prescribed in the fireplace installation instructions.

On new wood-burning fireplaces, first determine what you are burning. You should only be using seasoned wood, newspaper, or kindling. Firestarters can cause a smell. Seasoned fireplaces: what have you burned in the past? Have you cleaned the fireplace prior to burning? If you have used firestarters and/or prefabricated logs, these products are bound together with a wax-type substance, which does not dissipate. This wax can pool and has been found under the hearth refractory and can cause a very foul odor. Also check what is on top of the fireplace. Remove all objects from mantel to see if this eliminates the smell.

Hearth & Home Technologies’ remote controls work by radio frequency, which offers the unlikelihood of another remote control activating your individual gas fireplace product.

Infrared (light signals) is often used with television and stereo remotes and requires there be no interference between the hand-held and the receiver. Fireplace facings, louvers and different installation options make infrared an unreliable option for fireplaces. Also, the brightness of the flame interferes with infrared control systems.

Sonic or Sound is the third technology used with remote controls. The early sonic technology was used on television, but quickly abandoned due to limitation in channels and choices. Most Sonic technology is used in the pest control industry today.

The Quadra-Fire wood stoves incorporate secondary burn tubes, which are more efficient, burn cleaner and require less maintenance than stoves with catalytic converters. More than 50% of the heat from your wood stove comes from burning the smoke, and stoves with secondary burn tubes burn that smoke inside the firebox, instead of in your chimney. Generally, the Quadra-Fire wood stoves average fewer emissions versus the EPA standard of 6 grams per hour. They are very clean burning. And, over the life of a catalytic converter stove, you will need to replace the converter several times. This is quite a costly maintenance requirement. You will not need to replace the heat tubes on the Quadra-Fire stoves.

Your fan kit has a rheostat control (like a light dimmer). You can get more air from your fan by making sure the fan control is turned up to the desired level. The fan control can be found in the control area behind the lower louver of the fireplace, or on a wall switch with rheostat. We also provide optional remote controls which can control your fan speed from your favorite chair! Your dealer can help you with adding a remote control.

Our fans are purposely designed at lower CFMs (cubic feet per minute). There are two reasons for this. This first is to minimize fan noise. Second, a high velocity would tend to cool the air temperature coming out of the top louver of the fireplace. The fan is designed to move warm air into the room, not to move air clear across the room.

On gas fireplaces that are not brand new and are emitting some odor, try cleaning behind the upper and lower louvers. Dust can cause odor. Another source of odor can be the items you have on your mantel. Remove all objects from your mantel and then replace the objects one at a time. A third source of odor can be from the adhesives used in surround materials. This will need to be investigated by your installer. If these suggested sources don’t correctly identify the odor, contact your dealer where the fireplace was purchased and have your fireplace inspected.

No, absolutely not. A direct vent uses a high temperature glass panel to seal off the burn area of the fireplace from the interior of the home. It pulls 100% combustion air to feed the fire from outside the home. Because of its design, a direct vent gas fireplace will not affect the indoor air quality of your home. Since no air from your home is going up the chimney, a direct vent model is very efficient. Vent free should actually be called room vented since the by-products of gas combustion all spill back into the room. The single largest by-product of the gas combustion process is water vapor. Over sizing or overuse of a vent free hearth product can lead to excess moisture in a well built, tightly constructed home. Excess moisture inside the home can contribute to odors, mold and mildew inside the home.

If your system is controlled from an IntelliSwitch wall control, the batteries may be left in the unit. If not, install the batteries only when there is a power outage.

When the remote is in the thermostat mode (SMART-STAT and RCT-MLT models) and the temperature of the room has not exceeded the desired temperature setting by 2 degrees Fahrenheit or 1 degree Celsius the fireplace will not turn on and off. The thermostat is set with a 2 degree F (1 degree C) range to avoid continuous cycling of the fireplace.

The glass on a gas fireplace WILL reach very high temperatures. USE CAUTION: Carefully SUPERVISE children in the same room as your appliance; alert everyone to the hazards of high temperatures; do NOT operate with protective barriers removed; keep clothing, furniture, draperies and other combustibles away. Barriers such as screens over our direct vent glass help reduce the risk of burn from touching the glass. These screens are available through your local dealer.

While direct vent gas fireplaces are designed principally for their aesthetic value, we try to get as much heat output as possible to provide added value to the homeowner. It should be noted that while we are getting a lot of heat, we are passing the ANSI and UL standards for combustible temperatures. The allowable is 117°F above room temperature for combustibles. Average room temperature is 70-75°F; therefore a 187-192°F surface temperature can be expected. On a solid surface, 150°F is very hot to the touch (to put this in perspective, water boils at 212°F and the average bath water temperature is 110°F).

Each system is calibrated by the manufacturer and may not match exactly. If the temperature readings are within 3 degrees this is within the specification.

The temperature from one device to another is difficult to determine. The location of the thermostat is very important to the temperature that you are reading at any point in time. The important thing to remember is that you should develop a comfort area and the appliance will keep you at your comfort level rather than the exact temperature read out.

Intermittent Pilot Ignition is an electronic system, which uses an electrode to ignite the pilot gas. In turn, the pilot flame lights the main burner gas. The term Intermittent is used because the pilot burner flame is only present when the main burner is operating. When the main burner is off the pilot is also off. The IPI system ensures the pilot flame extends over the burner for immediate ignition and secondly conserves energy when the appliance is not in operation.
Intellifire, an ignition system exclusively featured in Heatilator, Heat & Glo & Quadra-Fire products, is an energy-saving pilot ignition system for gas fireplaces and inserts. It provides an ignition flame only when needed and has a battery backup system that supplies power to spark the ignition flame in the event of a power outage.

There are several possible causes of feeling cold air from a wood fireplace. You will want to make sure the damper is closed. Also check the installation manual for any other potential openings that may need to be shut. If the fireplace is mounted on cement versus plywood, that can also transfer cold into your home. If the chase area or doghouse is not insulated adequately, that is another possibility. Please check with your builder or installer on the insulation of the chase.

This is normal in the first few minutes of operation. If after the first 30 minutes of full burn you still have blue flames, an adjustment may be needed on your unit. For assistance with this, contact your dealer.

Sooting is a result of impingement caused by incomplete combustion, i.e. flames coming in contact with a surface, cooling the flame, and preventing combustion.

Most fans are wired into the fireplace with a fan sensor switch. This switch will activate the blower when the firebox heats up to a certain temperature. It will also automatically turn the blower off when the fireplace is turned off and the unit cools to a certain temperature. This sensor is provided so that you will not be circulating cold air in your home. The amount of time needed to heat up the fan sensor will differ depending on the model of your fireplace. It is common that blowers installed in Firebrick products will take longer to sense the heat and turn on your blower. Firebrick has greater insulating characteristics and holds the heat inside your firebox resulting in higher radiant heat and greater efficiencies

If your model has a standing pilot light, it does not require house current at any time to operate; or if your appliance has our patented IPI or IPI+ System, which works on a battery back up of 2 "D" or 4 "AA" batteries (depending on the particular ignition system), it will work in event of a power outage. You will need to install batteries for operation. If you have a fan or a remote control option, they will not work without power, but the appliance itself will burn and provide heat. (If you have a remote control, you may need to operate the appliance with the ON/Off switch in the control area of the appliance).

A damper clamp will come standard with your gas log set and MUST be installed to maintain a small opening at all times. This allows for the escape of any pilot exhaust. When the logs are in use the damper must be fully open.

Service

In many cases a gas fireplace has several facing and trim options. Fireplaces can be given a "face lift" by changing the stone facing or surrounds, and wood mantel options. Your local dealer can give you more details on the options for your particular fireplace, or visit our Fireside Furnishings website: www.firesidefurnishings.com.

Many of our gas fireplace models that have louvers or grills on the front can have a fan kit added. You will want to make sure that electricity is run to the junction box underneath the fireplace first, before ordering & installing a fan kit. You can test the junction box by plugging a lamp into the junction box and switching it on and off. Also make sure the circuit breaker is not tripped. If there is no electricity to the junction box you would have to run electric to the fireplace first before the fan kit could be installed. You can order a fan kit through your local dealer; installation instructions are packed with it.

No. The frequency of the remote control cannot be changed without special equipment, which is not readily available to homeowners and/or service companies. Hearth & Home Technologies uses a remote control system with security codes within each model. These security codes are burned into the transmitter of each model and cannot be changed. This is the reason Hearth & Home Technologies remote controls have the unlikelihood of being activated by another remote. If there is more than one Hearth & Home Technologies remote control at a home it is important that each hand-held transmitter has had the “learn” function activated to its designated receiver. If one hand-held transmitter was used in the “learn” activation for both receivers only one hand-held will function.

Each fireplace has a rating plate either inside the operating door or in the lower controls cavity. On that rating plate is your model number and serial number. Wood-burning fireplaces have a metal serial/model plate in the upper left side or right side of the firebox, or riveted on the smoke shield behind the screen. Gas burning fireplaces and inserts have a serial/model/rating plate in the lower cavity controls area. Gas stoves have a serial/model/rating plate attached to the back of the stove or inside the pedestal base.

Hearth & Home Technologies’ remote controls work by radio frequency, which offers the unlikelihood of another remote control activating your individual gas fireplace product.

Infrared (light signals) is often used with television and stereo remotes and requires there be no interference between the hand-held and the receiver. Fireplace facings, louvers and different installation options make infrared an unreliable option for fireplaces. Also, the brightness of the flame interferes with infrared control systems.

Sonic or Sound is the third technology used with remote controls. The early sonic technology was used on television, but quickly abandoned due to limitation in channels and choices. Most Sonic technology is used in the pest control industry today.

It is very important to clean your glass after the initial 3 hours of burn time. Failure to do so can cause permanent etching of your glass.

  1. Make sure your glass is completely cooled. It is also recommended to turn the gas off when servicing your appliance.
  2. Remove the front face or louvers of your fireplace; carefully remove the glass assembly of your fireplace (following the instructions in your manual) and lay it on a soft surface.
  3. Wipe both sides with household glass cleaner (do not use a product with ammonia), using a soft cloth.
  4. For heavy deposits, use Stove Bright Glass Cleaner , Rutland White Off Glass Cleaner, or other hard water deposit glass cleaner recommended by your servicing dealer.
  5. Carefully replace glass on front of fireplace (following the instructions in your manual), making sure glass assembly and front are secured.
  6. After this initial cleaning, clean your glass as often as necessary, particularly if adding new ember material. Never use any abrasive cleaners or cloths to clean your glass. Scratching can cause the glass to shatter.

CAUTION: ALWAYS REMOVE YOUR FIREPLACE GLASS PRIOR TO LIGHTING YOUR PILOT

STEP 1: Locate gas supply valve (typically behind louvers, below glass opening - may be red or blue).

STEP 2: Open valve by pivoting handle to be parallel to gas line.

STEP 3: Locate pilot assembly with spark igniter (located behind and below logs in the firebox - typically in the bottom center).

STEP 4: Then locate red or black igniter button.* Push igniter to verify spark at pilot area.

STEP 5: Locate the black or green valve control knob (knob with the words "ON", "OFF" and "PILOT" on it). Push in and rotate counter-clockwise until the word "pilot" is in the 6 o'clock position.**

STEP 6: While pressing and holding in the valve knob (in "PILOT" position - it should press in about 1/4"), press the red piezo button repeatedly (once per second) until the pilot ignites. If the pilot does not light, wait 5 minutes and try again. Once the pilot is lit, continue to hold the valve knob in for 30 seconds, then slowly release.

STEP 7: If the pilot light goes out, contact your nearest dealer for service. Remember to shut the gas supply valve off (picture #1). If it remains lit, press the valve knob in slightly and rotate counter-clockwise until the word "ON" is in the 6 o'clock position.

STEP 8: Finally, turn the unit's ON/OFF switch (or wall switch or remote control) to the "ON" position to start your fire. Make sure you put the glass front back on the fireplace prior to burning your fireplace. Make sure the glass is securely clamped on, at all points, prior to replacing the front.

STEP 9: Enjoy your fireplace!

* If you do not see a red or black spark igniter button, you do not have a manual ignition system. If power is actively supplied to your fireplace, simply turn the on/off button, wall switch or remote control to "on" to ignite your main burner.

** Note: Some valve assemblies may be inverted in their brackets. If yours appears to be the mirror image of picture #4, then the word "PILOT" will be in the 12 o'clock position to light the pilot, and "ON" will be set to the 12 o'clock position to turn on your main burner.

CAUTION: ALWAYS REMOVE YOUR FIREPLACE GLASS PRIOR TO LIGHTING YOUR PILOT

Please refer to the installation manual or users guide for your fireplace to see how the glass is attached to your specific model and instructions for removal.

Under normal operating conditions the batteries should last 6 – 12 months. Each of the batteries used in the hand-held transmitters should be producing 1.5V to 1.6V to operate. If the batteries are generating 1.3V to 1.35V or less the batteries should be replaced and can cause intermittent operation.

Your fan kit has a rheostat control (like a light dimmer). You can get more air from your fan by making sure the fan control is turned up to the desired level. The fan control can be found in the control area behind the lower louver of the fireplace, or on a wall switch with rheostat. We also provide optional remote controls which can control your fan speed from your favorite chair! Your dealer can help you with adding a remote control.

Our fans are purposely designed at lower CFMs (cubic feet per minute). There are two reasons for this. This first is to minimize fan noise. Second, a high velocity would tend to cool the air temperature coming out of the top louver of the fireplace. The fan is designed to move warm air into the room, not to move air clear across the room.

On gas fireplaces that are not brand new and are emitting some odor, try cleaning behind the upper and lower louvers. Dust can cause odor. Another source of odor can be the items you have on your mantel. Remove all objects from your mantel and then replace the objects one at a time. A third source of odor can be from the adhesives used in surround materials. This will need to be investigated by your installer. If these suggested sources don’t correctly identify the odor, contact your dealer where the fireplace was purchased and have your fireplace inspected.

No, absolutely not. A direct vent uses a high temperature glass panel to seal off the burn area of the fireplace from the interior of the home. It pulls 100% combustion air to feed the fire from outside the home. Because of its design, a direct vent gas fireplace will not affect the indoor air quality of your home. Since no air from your home is going up the chimney, a direct vent model is very efficient. Vent free should actually be called room vented since the by-products of gas combustion all spill back into the room. The single largest by-product of the gas combustion process is water vapor. Over sizing or overuse of a vent free hearth product can lead to excess moisture in a well built, tightly constructed home. Excess moisture inside the home can contribute to odors, mold and mildew inside the home.

Our fan kits come with a rheostat control (like a light dimmer). You can turn the control down to reduce the air noise from your fan. The fan control can be found in the control area behind the lower louver of the fireplace. We also provide optional remote controls which can control your fan speed and flame height from your favorite chair! Your dealer can help you with adding a remote control.

The following are the top reasons why remotes do not function:

1) Batteries do not have enough power or are installed incorrectly.
2) Misunderstanding on how the remote features operate the fireplace.
3) The slide switch on the receiver is not in the correct position.
4) The remote hand-held transmitter has not had the “learn” function activated to the receiver.
5) For standing pilot units, the thermopile must generate a minimum of 200 Millivolts. The fireplace requires more millivolts to operate via the remote control because it adds resistance to the system.
6) Defective component, for which replacement parts can be purchased or replaced under warranty within 1 year of the purchase of the remote.

1) The on/off switch on the fireplace and/or wall may be in the on position. This will over ride the remote control feature.
2) The remote is in the thermostat mode (SMART-STAT and RCT-MLT models) and the temperature of the room has not exceeded the desired temperature setting by 2 degrees Fahrenheit or 1 degree Celsius.
3) Batteries in the hand-held transmitter are old and underpowered. May work up close and will not work a few feet away.
4) Hand-held transmitter is outside of the 25’ of operation.
5) Hand-held transmitter has been dropped and the frequency has been moved off the frequency of the receiver.

When the remote is in the thermostat mode (SMART-STAT and RCT-MLT models) and the temperature of the room has not exceeded the desired temperature setting by 2 degrees Fahrenheit or 1 degree Celsius the fireplace will not turn on and off. The thermostat is set with a 2 degree F (1 degree C) range to avoid continuous cycling of the fireplace.

Each system is calibrated by the manufacturer and may not match exactly. If the temperature readings are within 3 degrees this is within the specification.

The temperature from one device to another is difficult to determine. The location of the thermostat is very important to the temperature that you are reading at any point in time. The important thing to remember is that you should develop a comfort area and the appliance will keep you at your comfort level rather than the exact temperature read out.

1) A hand-held transmitter. This is like a TV remote with which a person operates various features of the fireplace.
2) A receiver. This is located inside or near the fireplace and receives the radio frequency from the hand-held transmitter.
3) A Solenoid (for remote model RCT-MLT). This provides the option of a remote controlled variable flame. The solenoid is installed onto the regulator (located on the gas valve) of the fireplace to vary the gas pressure to the burner.

Excessive metal will deflect radio frequency in a direction that may not be in line with the receiver of your remote control. Interference of your radio frequency can cause the remote control to not respond properly to the hand-held transmitter. Hearth & Home Technologies has many built in safety functions to ensure that your remote control and fireplace operate in harmony. For this reason the receiver of the remote should not be installed to the very back of the fireplace. Large metal artwork can interfere with radio frequency.

Both the transmitter and receiver in model SMART-BATT are powered by batteries. Models SMART-STAT, RCT-MLT, RC-100, RC-200, and RC-300 are powered by batteries in the hand-held transmitters. The receiver is plugged into the junction box located in the bottom of the fireplace (Note: this requires an electrical hookup by qualified electrician at time of fireplace installation).

There are several possible causes of feeling cold air from a wood fireplace. You will want to make sure the damper is closed. Also check the installation manual for any other potential openings that may need to be shut. If the fireplace is mounted on cement versus plywood, that can also transfer cold into your home. If the chase area or doghouse is not insulated adequately, that is another possibility. Please check with your builder or installer on the insulation of the chase.

Gas Products

Operating cost will vary by region, by gas utility, and by fuel type. Based on national averages, a natural gas fireplace consuming 27,000 BTUs/hr will cost less than 20 cents/hr to enjoy. LP units run slightly higher. Your monthly gas bill should include your exact cost per therm (100,000 BTUs). Based on this rate, and the BTU input listed on the rating plate on your appliance, you can calculate the cost for your area.

Yes, provided the model includes a tempered glass front. It is also recommended that you do not install the fireplace where it is in danger of having water splash directly on it, nor install where there is a slippery surface where you are in danger of slipping or falling.

Yes, however, it’s best to confer with a local dealer to make sure the proper size and type gas unit is installed.

They can burn one or the other, but not both. You need to be sure the gas hearth appliance you have is set up for the type of gas fuel you intend to burn. Conversion kits are available which will allow a unit to be changed to match the proper fuel type.

Flame height adjustments are available on many gas units. Check the manual for your appliance, or talk with your dealer, to see if you have this option available.

No! Burning anything other than natural or LP gas in a gas fireplace or stove will create a potential fire hazard and present a danger to your home and its occupants. Only burn the gas fuel for which the unit was originally designed.

In an effort to deliver quality products, service, and safety, Hearth & Home Technologies, Inc. distributes our family of products exclusively through authorized and trained distributors and dealers. Occasionally, individuals will attempt to sell products online without the consent of the manufacturer. Heatilator, Heat & Glo, Harman and Quadra-Fire do not authorize the sale of products online. Here are a few things to consider if you are contemplating an online purchase of a quality hearth product.

Warranty - Heatilator, Heat & Glo or Quadra-Fire does not warranty products sold outside of our authorized dealer network, nor will they warranty service work on the product that is performed by anyone other than an authorized dealer. In addition, the warranty on our products applies to the original owner only and is nontransferable.

Customer Expectations - Our dealers are trained to evaluate your specific needs and suggest to you the products that will best meet those needs. When buying products online, you may be purchasing products that are not ideal for your situation and, as a result, be more costly than you anticipated. The products also require specific venting components with restrictions as to their installation which may not be evident in the purchase without a trained dealer to assess the installation application and recommend the appropriate venting scheme.

Shipping Damage - Our products are designed to ship to our customers using approved carriers and processes. The risk for damage increases if you attempt to ship product outside of our dealer network. We will not be responsible for any costs related to shipping damage.

Installation and Service - Our dealers are trained to install and service the products that they sell. We strongly recommend our products be installed and serviced by authorized dealers. Your warranty will be void if the product is not installed, operated and maintained in compliance with local building codes and with the instructions in the installer’s guide, owner’s guide and listing agent identification label furnished with the product. Your warranty will also be void if any service work is performed on the product by anyone other than an authorized representative. Furthermore, many local dealers will not service a fireplace they did not sell, making the authorized service of your product much more expensive. Lastly, the installation and set up of a product requires very specific installation and operational accessories. These accessories are often times not included in online sales, and can be very difficult and expensive to find after the fact.

For proper sales and service, find a local authorized dealer near you.

In many cases a gas fireplace has several facing and trim options. Fireplaces can be given a "face lift" by changing the stone facing or surrounds, and wood mantel options. Your local dealer can give you more details on the options for your particular fireplace, or visit our Fireside Furnishings website: www.firesidefurnishings.com.

Check with your local dealer to see if this is possible on your specific model fireplace.

Check with your local dealer to see if this is possible on your specific model fireplace.

No. The louvers allow room air to move around the heat exchanger. Blocking this air flow can cause fires and will void your manufacturer's warranty and possibly your homeowner's warranty.

Many of our gas fireplace models that have louvers or grills on the front can have a fan kit added. You will want to make sure that electricity is run to the junction box underneath the fireplace first, before ordering & installing a fan kit. You can test the junction box by plugging a lamp into the junction box and switching it on and off. Also make sure the circuit breaker is not tripped. If there is no electricity to the junction box you would have to run electric to the fireplace first before the fan kit could be installed. You can order a fan kit through your local dealer; installation instructions are packed with it.

Installation of our hearth products must be done in strict accordance with local or national building codes, and the unit's installation manual. We recommend that our products be installed by a factory-trained professional. You can find a factory-trained professional on this website under the Dealer Locator section.

You need to check with the manufacturer of your television. We follow the recommendations of the TV manufacturer. NOTE: we take no responsibility of any damage caused by the heat of the fireplace.

No. We make a wide variety of products that can be used in an outdoor porch, patio or open area under the Outdoor Lifestyles product line. You can view these products on this website under Outdoor Products.

Not on a direct vent or B vent model. A gas fireplace is an engineered system that includes the firebox, burner, logs, venting and options which are tested and listed by AGA or UL. Changing any of the specifications or placement of the logs could void your manufacturer's warranty, and possibly even your homeowner's warranty.

Not if your fireplace was shipped with a glass panel on the front. Direct vent fireplaces are sealed combustion systems and need the glass on to function properly. We sell optional screen mesh panels that go on the front of the glass that takes away any reflection, and adds an additional safety barrier against accidental contact with the hot glass panel. The other type of gas fireplaces we sell, called B-vent fireplaces, come with fixed, not sealed, glass fronts. You would need to check with your local dealer in the area to determine if the glass panel can be removed from this type of unit. Because removal of the glass is totally dependent on the specific unit installed, we cannot recommend that the glass be removed unless the specific model of unit denotes that it can be removed and the fireplace will still operate safely.

It's not recommended in climates that are high in humidity. Otherwise, you can turn the pilot off when you won’t be using your appliance for an extended period of time, and then use our on-line instructions to relight the pilot when needed.

No. The larger size of a masonry chimney is unsuitable for use with a factory built fireplace. We do have several models of wood burning or gas burning inserts that are designed for retrofit into an existing masonry fireplace, and they come with special venting that can be used inside an existing chimney. Your local dealer can help you pick the insert that best fits your needs.

No, with today’s venting options, direct vents can go literally anywhere in the home. The vent can terminate vertically through the roof or horizontally through an exterior wall. Your local dealer will be happy to assist you in determining the best venting option for your particular layout.

On the contrary, the glass panel keeps warm room air which your furnace has already heated from going up your fireplace flue. Direct vent fireplaces are excellent sources of zone heating by bringing room air in the bottom grill, heating and returning it to the room through the top grill.

No. The Manufacturer’s Suggested Retail Price (MSRP) shown on the website includes the fireplace or appliance only. Fronts, piping, surrounds, gas or electric connections, and installation will be in addition to this suggested price.

Each fireplace has a rating plate either inside the operating door or in the lower controls cavity. On that rating plate is your model number and serial number. Wood-burning fireplaces have a metal serial/model plate in the upper left side or right side of the firebox, or riveted on the smoke shield behind the screen. Gas burning fireplaces and inserts have a serial/model/rating plate in the lower cavity controls area. Gas stoves have a serial/model/rating plate attached to the back of the stove or inside the pedestal base.

The majority of our gas fireplaces and inserts are direct vent (DV). This means they have a fixed glass front which seals the gas burner and combustion firebox off from your home. 100% of the combustion air used by the fireplace comes from outside the home through a coaxial pipe. A smaller pipe inside the larger pipe eliminates all combustible gases, maintaining indoor air quality. The vent can be run horizontally through an outside wall, or vertically through the roof, depending on your preference.

Never, ever wash your logs. Remove the logs carefully from the fireplace in a box, take them outside and use a soft brush or vacuum to clean them. Make sure you replace the logs exactly as they were originally placed.

It is very important to clean your glass after the initial 3 hours of burn time. Failure to do so can cause permanent etching of your glass.

  1. Make sure your glass is completely cooled. It is also recommended to turn the gas off when servicing your appliance.
  2. Remove the front face or louvers of your fireplace; carefully remove the glass assembly of your fireplace (following the instructions in your manual) and lay it on a soft surface.
  3. Wipe both sides with household glass cleaner (do not use a product with ammonia), using a soft cloth.
  4. For heavy deposits, use Stove Bright Glass Cleaner , Rutland White Off Glass Cleaner, or other hard water deposit glass cleaner recommended by your servicing dealer.
  5. Carefully replace glass on front of fireplace (following the instructions in your manual), making sure glass assembly and front are secured.
  6. After this initial cleaning, clean your glass as often as necessary, particularly if adding new ember material. Never use any abrasive cleaners or cloths to clean your glass. Scratching can cause the glass to shatter.

CAUTION: ALWAYS REMOVE YOUR FIREPLACE GLASS PRIOR TO LIGHTING YOUR PILOT

STEP 1: Locate gas supply valve (typically behind louvers, below glass opening - may be red or blue).

STEP 2: Open valve by pivoting handle to be parallel to gas line.

STEP 3: Locate pilot assembly with spark igniter (located behind and below logs in the firebox - typically in the bottom center).

STEP 4: Then locate red or black igniter button.* Push igniter to verify spark at pilot area.

STEP 5: Locate the black or green valve control knob (knob with the words "ON", "OFF" and "PILOT" on it). Push in and rotate counter-clockwise until the word "pilot" is in the 6 o'clock position.**

STEP 6: While pressing and holding in the valve knob (in "PILOT" position - it should press in about 1/4"), press the red piezo button repeatedly (once per second) until the pilot ignites. If the pilot does not light, wait 5 minutes and try again. Once the pilot is lit, continue to hold the valve knob in for 30 seconds, then slowly release.

STEP 7: If the pilot light goes out, contact your nearest dealer for service. Remember to shut the gas supply valve off (picture #1). If it remains lit, press the valve knob in slightly and rotate counter-clockwise until the word "ON" is in the 6 o'clock position.

STEP 8: Finally, turn the unit's ON/OFF switch (or wall switch or remote control) to the "ON" position to start your fire. Make sure you put the glass front back on the fireplace prior to burning your fireplace. Make sure the glass is securely clamped on, at all points, prior to replacing the front.

STEP 9: Enjoy your fireplace!

* If you do not see a red or black spark igniter button, you do not have a manual ignition system. If power is actively supplied to your fireplace, simply turn the on/off button, wall switch or remote control to "on" to ignite your main burner.

** Note: Some valve assemblies may be inverted in their brackets. If yours appears to be the mirror image of picture #4, then the word "PILOT" will be in the 12 o'clock position to light the pilot, and "ON" will be set to the 12 o'clock position to turn on your main burner.

CAUTION: ALWAYS REMOVE YOUR FIREPLACE GLASS PRIOR TO LIGHTING YOUR PILOT

Please refer to the installation manual or users guide for your fireplace to see how the glass is attached to your specific model and instructions for removal.

A pilot light will burn 800 to 1500 BTUs/hr. Your monthly gas bill should include your exact cost per "therm" (100,000 BTUs). Based on this rate you can calculate the cost for your area to operate a pilot light.

Although the frequency of your fireplace servicing and maintenance will depend on use and the type of installation, you should have a qualified service technician perform an appliance check-up at the beginning of each heating season.

Your fan kit has a rheostat control (like a light dimmer). You can get more air from your fan by making sure the fan control is turned up to the desired level. The fan control can be found in the control area behind the lower louver of the fireplace, or on a wall switch with rheostat. We also provide optional remote controls which can control your fan speed from your favorite chair! Your dealer can help you with adding a remote control.

On gas fireplaces that are not brand new and are emitting some odor, try cleaning behind the upper and lower louvers. Dust can cause odor. Another source of odor can be the items you have on your mantel. Remove all objects from your mantel and then replace the objects one at a time. A third source of odor can be from the adhesives used in surround materials. This will need to be investigated by your installer. If these suggested sources don’t correctly identify the odor, contact your dealer where the fireplace was purchased and have your fireplace inspected.

No, absolutely not. A direct vent uses a high temperature glass panel to seal off the burn area of the fireplace from the interior of the home. It pulls 100% combustion air to feed the fire from outside the home. Because of its design, a direct vent gas fireplace will not affect the indoor air quality of your home. Since no air from your home is going up the chimney, a direct vent model is very efficient. Vent free should actually be called room vented since the by-products of gas combustion all spill back into the room. The single largest by-product of the gas combustion process is water vapor. Over sizing or overuse of a vent free hearth product can lead to excess moisture in a well built, tightly constructed home. Excess moisture inside the home can contribute to odors, mold and mildew inside the home.

Our fan kits come with a rheostat control (like a light dimmer). You can turn the control down to reduce the air noise from your fan. The fan control can be found in the control area behind the lower louver of the fireplace. We also provide optional remote controls which can control your fan speed and flame height from your favorite chair! Your dealer can help you with adding a remote control.

If your system is controlled from an IntelliSwitch wall control, the batteries may be left in the unit. If not, install the batteries only when there is a power outage.

The glass on a gas fireplace WILL reach very high temperatures. USE CAUTION: Carefully SUPERVISE children in the same room as your appliance; alert everyone to the hazards of high temperatures; do NOT operate with protective barriers removed; keep clothing, furniture, draperies and other combustibles away. Barriers such as screens over our direct vent glass help reduce the risk of burn from touching the glass. These screens are available through your local dealer.

While direct vent gas fireplaces are designed principally for their aesthetic value, we try to get as much heat output as possible to provide added value to the homeowner. It should be noted that while we are getting a lot of heat, we are passing the ANSI and UL standards for combustible temperatures. The allowable is 117°F above room temperature for combustibles. Average room temperature is 70-75°F; therefore a 187-192°F surface temperature can be expected. On a solid surface, 150°F is very hot to the touch (to put this in perspective, water boils at 212°F and the average bath water temperature is 110°F).

An outside air kit provides additional combustion air to the fireplace that feeds the fire with oxygen from outside your home. This will help the performance on any fireplace installed in tightly-constructed or well-insulated home. If you are installing a wood burning or B-Vent gas fireplace, you should consider installation of an outside air kit.

Zero clearance has two meanings. The first is whether or not the fireplace can be placed on a floor without footings. All of our fireplaces are classified as zero clearance, meaning they do not need special footings. The second meaning of zero clearance is if you are able to finish up to the face of the fireplace, so that no metal shows after installation is complete. There are several models on our website that are capable of this clean-faced, zero clearance finish. Check with your local dealer on which models are suitable for this type of installation.

You will need to contact the dealer in your area to order a new log. Do not use your fireplace until your log set is complete and placed properly. Operating the fireplace with an incomplete log set, or one which is improperly placed, may cause sooting.

Heatilator carries “Reveal” model B-vent gas fireplaces which are sold without fixed glass on the front. You can view these fireplaces at www.heatilator.com.

A flue is another name for the fireplace chimney or venting system.

Intermittent Pilot Ignition is an electronic system, which uses an electrode to ignite the pilot gas. In turn, the pilot flame lights the main burner gas. The term Intermittent is used because the pilot burner flame is only present when the main burner is operating. When the main burner is off the pilot is also off. The IPI system ensures the pilot flame extends over the burner for immediate ignition and secondly conserves energy when the appliance is not in operation.
Intellifire, an ignition system exclusively featured in Heatilator, Heat & Glo & Quadra-Fire products, is an energy-saving pilot ignition system for gas fireplaces and inserts. It provides an ignition flame only when needed and has a battery backup system that supplies power to spark the ignition flame in the event of a power outage.

A B-vent must be vented vertically and uses fresh air from inside the home to provide oxygen to the fire. A direct vent has a sealed glass front and pulls all of its fresh air from outside the home. Direct vents can be vented vertically or horizontally through an exterior wall. Direct vents are a completely sealed system; B-vent appliances are not.

Steady State: An efficiency rating is testing only the efficiency of the fireplace when it is burning. AFUE (Annual Fuel Utilization Efficiency): Both the on cycle and off cycle are calculated in this rating. By including the off cycles (when the fireplace is turned off) a more accurate yearly operational cost can be estimated.

On a new gas fireplace there is a curing time or burn-in time. When initially burning your new gas fireplace, the oils, etc. from manufacturing will be burning off the fireplace. We recommend burning the fireplace 3 hours; completely cooling down the fireplace, removing the glass and cleaning it with household glass cleaner or Glass Bright; replacing the glass & continuing to burn the fireplace an additional 9-21 hours. (Make sure you re-latch the glass so it is securely fastened on your fireplace.) If necessary, open a window to release any odor during this process. This should eliminate the manufacturing smell on a new fireplace.

There are several possible causes of feeling cold air from a wood fireplace. You will want to make sure the damper is closed. Also check the installation manual for any other potential openings that may need to be shut. If the fireplace is mounted on cement versus plywood, that can also transfer cold into your home. If the chase area or doghouse is not insulated adequately, that is another possibility. Please check with your builder or installer on the insulation of the chase.

This is normal in the first few minutes of operation. If after the first 30 minutes of full burn you still have blue flames, an adjustment may be needed on your unit. For assistance with this, contact your dealer.

Sooting is a result of impingement caused by incomplete combustion, i.e. flames coming in contact with a surface, cooling the flame, and preventing combustion.

Most fans are wired into the fireplace with a fan sensor switch. This switch will activate the blower when the firebox heats up to a certain temperature. It will also automatically turn the blower off when the fireplace is turned off and the unit cools to a certain temperature. This sensor is provided so that you will not be circulating cold air in your home. The amount of time needed to heat up the fan sensor will differ depending on the model of your fireplace. It is common that blowers installed in Firebrick products will take longer to sense the heat and turn on your blower. Firebrick has greater insulating characteristics and holds the heat inside your firebox resulting in higher radiant heat and greater efficiencies

If your model has a standing pilot light, it does not require house current at any time to operate; or if your appliance has our patented IPI or IPI+ System, which works on a battery back up of 2 "D" or 4 "AA" batteries (depending on the particular ignition system), it will work in event of a power outage. You will need to install batteries for operation. If you have a fan or a remote control option, they will not work without power, but the appliance itself will burn and provide heat. (If you have a remote control, you may need to operate the appliance with the ON/Off switch in the control area of the appliance).

Wood Products

You can if you have a heat circulating model, which means there are louvers in the top and bottom facing of the fireplace, and if there is electrical power to the junction box behind the lower louver, then you can easily install a fan kit.

No. Doing so will void the warranty on your fireplace and possibly void your homeowners insurance. An unvented gas log set that complies with the ANSI Z21.60 standard as a vented gas log set can be used as long as the damper is removed from the unit, but any other type of unvented log set will cause hazardous conditions.

In an effort to deliver quality products, service, and safety, Hearth & Home Technologies, Inc. distributes our family of products exclusively through authorized and trained distributors and dealers. Occasionally, individuals will attempt to sell products online without the consent of the manufacturer. Heatilator, Heat & Glo, Harman and Quadra-Fire do not authorize the sale of products online. Here are a few things to consider if you are contemplating an online purchase of a quality hearth product.

Warranty - Heatilator, Heat & Glo or Quadra-Fire does not warranty products sold outside of our authorized dealer network, nor will they warranty service work on the product that is performed by anyone other than an authorized dealer. In addition, the warranty on our products applies to the original owner only and is nontransferable.

Customer Expectations - Our dealers are trained to evaluate your specific needs and suggest to you the products that will best meet those needs. When buying products online, you may be purchasing products that are not ideal for your situation and, as a result, be more costly than you anticipated. The products also require specific venting components with restrictions as to their installation which may not be evident in the purchase without a trained dealer to assess the installation application and recommend the appropriate venting scheme.

Shipping Damage - Our products are designed to ship to our customers using approved carriers and processes. The risk for damage increases if you attempt to ship product outside of our dealer network. We will not be responsible for any costs related to shipping damage.

Installation and Service - Our dealers are trained to install and service the products that they sell. We strongly recommend our products be installed and serviced by authorized dealers. Your warranty will be void if the product is not installed, operated and maintained in compliance with local building codes and with the instructions in the installer’s guide, owner’s guide and listing agent identification label furnished with the product. Your warranty will also be void if any service work is performed on the product by anyone other than an authorized representative. Furthermore, many local dealers will not service a fireplace they did not sell, making the authorized service of your product much more expensive. Lastly, the installation and set up of a product requires very specific installation and operational accessories. These accessories are often times not included in online sales, and can be very difficult and expensive to find after the fact.

For proper sales and service, find a local authorized dealer near you.

Glass doors are available for current model fireplaces. Check with your local dealer on availability of doors for older models. It is important that you purchase glass doors that the manufacturer of your fireplace sells for your particular model. Using a non-approved door can block off cooling air into the firebox chassis and cause a potential fire hazard.

Installation of our hearth products must be done in strict accordance with local or national building codes, and the unit's installation manual. We recommend that our products be installed by a factory-trained professional. You can find a factory-trained professional on this website under the Dealer Locator section.

Not if your fireplace was shipped with a glass panel on the front. Direct vent fireplaces are sealed combustion systems and need the glass on to function properly. We sell optional screen mesh panels that go on the front of the glass that takes away any reflection, and adds an additional safety barrier against accidental contact with the hot glass panel. The other type of gas fireplaces we sell, called B-vent fireplaces, come with fixed, not sealed, glass fronts. You would need to check with your local dealer in the area to determine if the glass panel can be removed from this type of unit. Because removal of the glass is totally dependent on the specific unit installed, we cannot recommend that the glass be removed unless the specific model of unit denotes that it can be removed and the fireplace will still operate safely.

No. The Manufacturer’s Suggested Retail Price (MSRP) shown on the website includes the fireplace or appliance only. Fronts, piping, surrounds, gas or electric connections, and installation will be in addition to this suggested price.

On new wood-burning fireplaces, first determine what you are burning. You should only be using seasoned wood, newspaper, or kindling. Firestarters can cause a smell. Seasoned fireplaces: what have you burned in the past? Have you cleaned the fireplace prior to burning? If you have used firestarters and/or prefabricated logs, these products are bound together with a wax-type substance, which does not dissipate. This wax can pool and has been found under the hearth refractory and can cause a very foul odor. Also check what is on top of the fireplace. Remove all objects from mantel to see if this eliminates the smell.

Each fireplace has a rating plate either inside the operating door or in the lower controls cavity. On that rating plate is your model number and serial number. Wood-burning fireplaces have a metal serial/model plate in the upper left side or right side of the firebox, or riveted on the smoke shield behind the screen. Gas burning fireplaces and inserts have a serial/model/rating plate in the lower cavity controls area. Gas stoves have a serial/model/rating plate attached to the back of the stove or inside the pedestal base.

The Quadra-Fire wood stoves incorporate secondary burn tubes, which are more efficient, burn cleaner and require less maintenance than stoves with catalytic converters. More than 50% of the heat from your wood stove comes from burning the smoke, and stoves with secondary burn tubes burn that smoke inside the firebox, instead of in your chimney. Generally, the Quadra-Fire wood stoves average fewer emissions versus the EPA standard of 6 grams per hour. They are very clean burning. And, over the life of a catalytic converter stove, you will need to replace the converter several times. This is quite a costly maintenance requirement. You will not need to replace the heat tubes on the Quadra-Fire stoves.

For vented gas log sets, you need to remove the log set and grate, have the gas line capped, and install a grate rated for natural wood. Also check the damper to make sure it has not been removed and is functioning properly; if needed, a damper repair kit may be available (and installed) to make the unit fully functioning as a wood-burning fireplace again.

While they produce some radiant heat, most wood-burning fireplaces are primarily decorative. Even heat circulating models still pull a tremendous amount of air from the home. There are several wood-burning models that are efficient and clean burning. We also have several wood-burning stoves and inserts that are very efficient.

The doors should always be fully open or fully closed. Glass doors should be fully open when starting a fire and when the fire is burning strongly. The glass doors should be closed as the fire dies down to minimize the amount of room air going up the fireplace chimney. When burning gas logs in a wood-burning fireplace, the glass doors should always be fully open when the gas logs are burning. ALWAYS keep the screen mesh on your fireplace closed when using the fireplace to guard against sparks popping out of the firebox area. If you have a see-through wood-burning fireplace, the doors should be either closed or open on both sides when burning.

Your decision really comes down to how much a priority heating efficiency is for you. If you want a lot of heat from your fireplace, you should consider a direct vent gas insert. From a cost standpoint, an insert will cost approximately five times the cost of a nice gas log set. However, since the insert is very efficient, it will pay for itself over a period of a few years in gas bill savings. We offer both a full line of inserts and vented gas logs to choose from. Installing room-vented or vent free log sets in our wood-burning fireplaces is unacceptable. Doing so will void your warranty on the fireplace and possibly your homeowners insurance.

Our fans are purposely designed at lower CFMs (cubic feet per minute). There are two reasons for this. This first is to minimize fan noise. Second, a high velocity would tend to cool the air temperature coming out of the top louver of the fireplace. The fan is designed to move warm air into the room, not to move air clear across the room.

Our fan kits come with a rheostat control (like a light dimmer). You can turn the control down to reduce the air noise from your fan. The fan control can be found in the control area behind the lower louver of the fireplace. We also provide optional remote controls which can control your fan speed and flame height from your favorite chair! Your dealer can help you with adding a remote control.

Yes. We recommend annual service of your fireplace by a qualified serviceperson. This will ensure that your appliance is functioning properly.

An outside air kit provides additional combustion air to the fireplace that feeds the fire with oxygen from outside your home. This will help the performance on any fireplace installed in tightly-constructed or well-insulated home. If you are installing a wood burning or B-Vent gas fireplace, you should consider installation of an outside air kit.

Zero clearance has two meanings. The first is whether or not the fireplace can be placed on a floor without footings. All of our fireplaces are classified as zero clearance, meaning they do not need special footings. The second meaning of zero clearance is if you are able to finish up to the face of the fireplace, so that no metal shows after installation is complete. There are several models on our website that are capable of this clean-faced, zero clearance finish. Check with your local dealer on which models are suitable for this type of installation.

If your fireplace does not have a gas starter, arrange kindling (small diameter sticks) in a crisscross pattern on top of crumpled newspaper under the grate before arranging the logs. Arrange logs in a safe way to ensure that logs don’t roll out during burning. Note that the first few fires you build in your wood-burning fireplace should be small to help avoid excess cracking or spidering in the refractory. NOTE: Do not over fill your fireplace, as this will cause unsafe operation.

There are several possible causes of feeling cold air from a wood fireplace. You will want to make sure the damper is closed. Also check the installation manual for any other potential openings that may need to be shut. If the fireplace is mounted on cement versus plywood, that can also transfer cold into your home. If the chase area or doghouse is not insulated adequately, that is another possibility. Please check with your builder or installer on the insulation of the chase.

Electric Products

In most areas it only costs two cents per hour to operate the flames and up to 22 cents per hour with the flames and the heaters on. The thermostat for the heater will automatically turn on and off per your setting to keep your room at the desired temperature. The thermostat will also lower your operating costs - frequently 50% lower or more.

All models are tested to UL standards and will automatically shut off in the unlikely event they overheat. They are clean burning and do not put fumes and moisture in your home as do "vent-free" fireplaces.

In an effort to deliver quality products, service, and safety, Hearth & Home Technologies, Inc. distributes our family of products exclusively through authorized and trained distributors and dealers. Occasionally, individuals will attempt to sell products online without the consent of the manufacturer. Heatilator, Heat & Glo, Harman and Quadra-Fire do not authorize the sale of products online. Here are a few things to consider if you are contemplating an online purchase of a quality hearth product.

Warranty - Heatilator, Heat & Glo or Quadra-Fire does not warranty products sold outside of our authorized dealer network, nor will they warranty service work on the product that is performed by anyone other than an authorized dealer. In addition, the warranty on our products applies to the original owner only and is nontransferable.

Customer Expectations - Our dealers are trained to evaluate your specific needs and suggest to you the products that will best meet those needs. When buying products online, you may be purchasing products that are not ideal for your situation and, as a result, be more costly than you anticipated. The products also require specific venting components with restrictions as to their installation which may not be evident in the purchase without a trained dealer to assess the installation application and recommend the appropriate venting scheme.

Shipping Damage - Our products are designed to ship to our customers using approved carriers and processes. The risk for damage increases if you attempt to ship product outside of our dealer network. We will not be responsible for any costs related to shipping damage.

Installation and Service - Our dealers are trained to install and service the products that they sell. We strongly recommend our products be installed and serviced by authorized dealers. Your warranty will be void if the product is not installed, operated and maintained in compliance with local building codes and with the instructions in the installer’s guide, owner’s guide and listing agent identification label furnished with the product. Your warranty will also be void if any service work is performed on the product by anyone other than an authorized representative. Furthermore, many local dealers will not service a fireplace they did not sell, making the authorized service of your product much more expensive. Lastly, the installation and set up of a product requires very specific installation and operational accessories. These accessories are often times not included in online sales, and can be very difficult and expensive to find after the fact.

For proper sales and service, find a local authorized dealer near you.

Installation of our hearth products must be done in strict accordance with local or national building codes, and the unit's installation manual. We recommend that our products be installed by a factory-trained professional. You can find a factory-trained professional on this website under the Dealer Locator section.

We offer several models with doors that open and a variety of fronts, doors, trim packages and finishing options - especially for our 36" models.

All of our electric hearth products come with heaters and the flames can be used with or without the heater on. It can be a no heat fireplace! Some models can be wired to 240 volts with a heat output up to 10,000 BTUs.

No. The Manufacturer’s Suggested Retail Price (MSRP) shown on the website includes the fireplace or appliance only. Fronts, piping, surrounds, gas or electric connections, and installation will be in addition to this suggested price.

Each fireplace has a rating plate either inside the operating door or in the lower controls cavity. On that rating plate is your model number and serial number. Wood-burning fireplaces have a metal serial/model plate in the upper left side or right side of the firebox, or riveted on the smoke shield behind the screen. Gas burning fireplaces and inserts have a serial/model/rating plate in the lower cavity controls area. Gas stoves have a serial/model/rating plate attached to the back of the stove or inside the pedestal base.

Most units can be hardwired by an electrician within a few hours. No venting or gas lines are needed, which can save you hundreds of dollars in materials for venting components & labor for installation.

They use optic technology with a rotisserie flame and a glowing ember bed to look like a wood fire. They can be finished off with wood cabinets, brick, stone and marble or a wide variety of finishing products for fireplaces.

Zero clearance has two meanings. The first is whether or not the fireplace can be placed on a floor without footings. All of our fireplaces are classified as zero clearance, meaning they do not need special footings. The second meaning of zero clearance is if you are able to finish up to the face of the fireplace, so that no metal shows after installation is complete. There are several models on our website that are capable of this clean-faced, zero clearance finish. Check with your local dealer on which models are suitable for this type of installation.

Remote Controls

Yes! However, there is an operational priority (Pecking order) of the various ways to turn your fireplace ON or OFF. Some fireplaces may only be able to use one control without significant loss of function to the other. The highest priority goes to the ON/OFF switch located near the valve assembly. For example, if you have the fireplace is turned “ON” via this switch, it will negate the wall switch and ON/OFF feature of your remote control.

Next, the wall switch takes priority over the remote control. In other words, if the wall switch is in the “ON” position and the units switch is in the “OFF” position, the remote control will not be able to turn the fireplace on or off. In either case, the RCT-MLT functions will work unless the "on- off" feature of the wall switch or fireplace switch is in the “ON” position.

No. The frequency of the remote control cannot be changed without special equipment, which is not readily available to homeowners and/or service companies. Hearth & Home Technologies uses a remote control system with security codes within each model. These security codes are burned into the transmitter of each model and cannot be changed. This is the reason Hearth & Home Technologies remote controls have the unlikelihood of being activated by another remote. If there is more than one Hearth & Home Technologies remote control at a home it is important that each hand-held transmitter has had the “learn” function activated to its designated receiver. If one hand-held transmitter was used in the “learn” activation for both receivers only one hand-held will function.

Hearth & Home Technologies remote controls have a manual switch on the receiver that can be turned to the OFF position. This switch is manual and will break the contact with the power source, whether it is battery or 120V power. This switch is just like the main power switch that controls any electrical appliance. It is completely unnecessary to unplug or remove batteries from the receiver.

Taking the batteries out of the hand held transmitter will not guarantee against accidental activation. Remember that each remote is equipped with a safety feature, which turns the fireplace off after 9 hours of continuous usage, when operated in the “manual mode”.

Operating the fireplace for longer than a continuous 9 hours is not a safety issue, but can cause the temperature in the room of the fireplace to reach higher than normal temperatures. It is always required to maintain the necessary clearance to combustibles as prescribed in the fireplace installation instructions.

Hearth & Home Technologies’ remote controls work by radio frequency, which offers the unlikelihood of another remote control activating your individual gas fireplace product.

Infrared (light signals) is often used with television and stereo remotes and requires there be no interference between the hand-held and the receiver. Fireplace facings, louvers and different installation options make infrared an unreliable option for fireplaces. Also, the brightness of the flame interferes with infrared control systems.

Sonic or Sound is the third technology used with remote controls. The early sonic technology was used on television, but quickly abandoned due to limitation in channels and choices. Most Sonic technology is used in the pest control industry today.

The FCC in the United States and IC in Canada regulate the distance in which a radio frequency from the hand-held transmitter can operate. In optimum conditions, this distance is 90 feet. Since there are many things than interfere with radio frequency the maximum realistic distance from which a hand-held transmitter will communicate with the receiver is 25 feet. Radio frequency will go through normal residential constructed walls (wood, plaster, drywall), but distance will be reduced traveling through walls.

Under normal operating conditions the batteries should last 6 – 12 months. Each of the batteries used in the hand-held transmitters should be producing 1.5V to 1.6V to operate. If the batteries are generating 1.3V to 1.35V or less the batteries should be replaced and can cause intermittent operation.

The following are the top reasons why remotes do not function:

1) Batteries do not have enough power or are installed incorrectly.
2) Misunderstanding on how the remote features operate the fireplace.
3) The slide switch on the receiver is not in the correct position.
4) The remote hand-held transmitter has not had the “learn” function activated to the receiver.
5) For standing pilot units, the thermopile must generate a minimum of 200 Millivolts. The fireplace requires more millivolts to operate via the remote control because it adds resistance to the system.
6) Defective component, for which replacement parts can be purchased or replaced under warranty within 1 year of the purchase of the remote.

1) The on/off switch on the fireplace and/or wall may be in the on position. This will over ride the remote control feature.
2) The remote is in the thermostat mode (SMART-STAT and RCT-MLT models) and the temperature of the room has not exceeded the desired temperature setting by 2 degrees Fahrenheit or 1 degree Celsius.
3) Batteries in the hand-held transmitter are old and underpowered. May work up close and will not work a few feet away.
4) Hand-held transmitter is outside of the 25’ of operation.
5) Hand-held transmitter has been dropped and the frequency has been moved off the frequency of the receiver.

When the remote is in the thermostat mode (SMART-STAT and RCT-MLT models) and the temperature of the room has not exceeded the desired temperature setting by 2 degrees Fahrenheit or 1 degree Celsius the fireplace will not turn on and off. The thermostat is set with a 2 degree F (1 degree C) range to avoid continuous cycling of the fireplace.

Each system is calibrated by the manufacturer and may not match exactly. If the temperature readings are within 3 degrees this is within the specification.

The temperature from one device to another is difficult to determine. The location of the thermostat is very important to the temperature that you are reading at any point in time. The important thing to remember is that you should develop a comfort area and the appliance will keep you at your comfort level rather than the exact temperature read out.

1) A hand-held transmitter. This is like a TV remote with which a person operates various features of the fireplace.
2) A receiver. This is located inside or near the fireplace and receives the radio frequency from the hand-held transmitter.
3) A Solenoid (for remote model RCT-MLT). This provides the option of a remote controlled variable flame. The solenoid is installed onto the regulator (located on the gas valve) of the fireplace to vary the gas pressure to the burner.

Excessive metal will deflect radio frequency in a direction that may not be in line with the receiver of your remote control. Interference of your radio frequency can cause the remote control to not respond properly to the hand-held transmitter. Hearth & Home Technologies has many built in safety functions to ensure that your remote control and fireplace operate in harmony. For this reason the receiver of the remote should not be installed to the very back of the fireplace. Large metal artwork can interfere with radio frequency.

Both the transmitter and receiver in model SMART-BATT are powered by batteries. Models SMART-STAT, RCT-MLT, RC-100, RC-200, and RC-300 are powered by batteries in the hand-held transmitters. The receiver is plugged into the junction box located in the bottom of the fireplace (Note: this requires an electrical hookup by qualified electrician at time of fireplace installation).

Hearth & Home Technologies offers several remote options with different features and functions to fit the different needs of today homeowners. They are all compact in size to fit the palm of your hand and come with a wall mounting bracket for easy storage.

SMART-BATT - This remote is perfect for you if your fireplace was previous installed without power and it would be too costly or impossible to wire electricity to it. This remote offers the feature of turning the flame on and off manually or by thermostatic temperature control. Count down timer system (15 min to 9 hours). 24 hour clock. Low battery indicator icon. Safety Feature: child proof setting to disable the on/off button and manual shutdown after 9 hours of continuous operation.

SMART-STAT –120 volts must be wired to the fireplace. This remote is ideal for the homeowner who wants the functions of a wall thermostat and the convenience of a remote control. Use manual or thermostatic settings to operate the fireplace at desired temperature between 45 to 99 degrees. Count down timer system (15 min to 9 hours). 24 hour clock. Low battery indicator icon. Safety Features: A child proof setting to disable the on/off button is also standard and manual shutdown after 9 hours of continuous operation.

RCT-MLT – If you enjoy having the best, then this remote is ideally suited for you. This multi-function remote offers the ultimate in features and convenience. It can conveniently do the following with just the touch of a button:
- Turns the flame on and off manually.
- Functions as a remote thermostat.
- Has an automatic timer function that allows you to turn the fireplace on for a desired amount of time between 1 to 90 minutes.
- Easily adjusts your fan setting (High, Medium, Low).
- An LED/LCD digital read out of the room’s temperature.
- Safety features; If the fireplace is turned on manually or by the thermostat and is on constantly for 9 hours the remote will turn the fireplace off.
- Child Proof setting to disable the on/off button is also standard.

Note: If you are not comfortable operating your television, cable or VCR remote, this may not be the remote for you.

Remote Controls are a consumer convenience. They are great for the busy lifestyles of today and will enhance the relaxing mood created by our gas fireplace by allowing the user to relax in their favorite chair and operate their fireplace while reclining in comfort. They are especially convenient in large rooms where a switch on the fireplace or on the wall is not always easily accessed. It is also an extremely popular option for bed/bath sitting rooms.

Your wall switch may be in child proof mode. When this is set, only the arrows will have functionality. The appliance can enter child proof mode when the fireplace is on or off.

To exit child proof mode: Press the Up Arrow Button twice and Down Arrow Button once. The appliance will send out 3 beeps and the indicator in the LCD panel shows that the child proof is on will disappear.

To enter child proof mode: Press the Up Arrow Button twice and Down Arrow Button once. The unit will send out 3 beeps and an indicator in the LCD panel will show that the child proof is on.

Gas Logs

The flames are not adjustable.

Yes, however, you must contact your local dealer to do the conversion for you.

No. The hearth kit is designed to work with only the appropriate gas logs. Attempting this could result in injury, damage or worse. Additionally, burning wood voids the warranty of the hearth kit. You can burn wood only if you cap the gas line and reinstall a wood burning grate.

No. You must leave the doors open when you are operating RealWood Elite gas logs to avoid damaging the controls.

The Hearth Kit can easily work with a left side gas line. Consult the installation manual for instructions.

Never, ever wash your logs. Remove the logs carefully from the fireplace in a box, take them outside and use a soft brush or vacuum to clean them. Make sure you replace the logs exactly as they were originally placed.

For vented gas log sets, you need to remove the log set and grate, have the gas line capped, and install a grate rated for natural wood. Also check the damper to make sure it has not been removed and is functioning properly; if needed, a damper repair kit may be available (and installed) to make the unit fully functioning as a wood-burning fireplace again.

The installation manual includes detailed diagrams showing where the logs must be placed to operate at the product's optimum level.

Proper sizing is determined by the size of the fireplace base and the overall size of the Gas Log and Hearth Kit, which requires measuring the front width, back width, depth and height of the fireplace. Getting logs or controls too tight to the sides can cause damage to the fireplaces and gas logs controls.

There are several different models you can view on our website. In addition, the Real Wood Elite gas log sets are used in conjunction with one of three Hearth Kits: 1. Match Light Hearth Kit – system lights with a struck match. 2. Safety Pilot Hearth Kit – system prevents the flow of gas when the appliance is not in use. 3. Millivolt Hearth Kit – system available in either LP gas or natural gas; A remote control or wall switch is available for use with the Millivolt Hearth Kit.

Cost will vary from product to product based on the BTU input and the type of gas used. Contact your local fuel provider with the amount of BTU's input and they should be able to relate it to the local, current fuel costs.

Gas logs will provide radiant heat in the general hearth area. Gas logs are easy to use, require little maintenance, and enhance the aesthetic appeal of your fireplace whether on or off. Use in conjunction with glass doors will improve their heating capacity. For maximized heat output, a full direct vent insert should be considered.

RealWood Elite logs are made of high temperature fiber material. Our design ensures a lifetime of enjoyment.

You will need to contact the dealer in your area to order a new log. Do not use your fireplace until your log set is complete and placed properly. Operating the fireplace with an incomplete log set, or one which is improperly placed, may cause sooting.

A safety pilot prevents the flow of gas when the appliance is not in use.

A remote control and/or wall switch requires a Millivolt valve system. The wall switch requires low voltage electrical wiring.

Minimum sizing is determined by consulting the measurements provided in the installation manual. Your local dealer will provide assistance in properly sizing your gas log set.

The cost will vary from market to market, and will vary more depending on the degree of difficulty in getting a gas line to the fireplace. We strongly suggest you use a factory trained installer for you installation.

A maintenance checkup at least every other year will result in minimal performance issues and help prevent any issues.

Sooting is a result of impingement caused by incomplete combustion, i.e. flames coming in contact with a surface, cooling the flame, and preventing combustion.

Gas logs create a beautiful fire that will liven up a party or enhance a relaxing, quiet atmosphere. Gas logs are convenient, easy to operate and require minimal maintenance.

A damper clamp will come standard with your gas log set and MUST be installed to maintain a small opening at all times. This allows for the escape of any pilot exhaust. When the logs are in use the damper must be fully open.

Other

You can if you have a heat circulating model, which means there are louvers in the top and bottom facing of the fireplace, and if there is electrical power to the junction box behind the lower louver, then you can easily install a fan kit.

No. Doing so will void the warranty on your fireplace and possibly void your homeowners insurance. An unvented gas log set that complies with the ANSI Z21.60 standard as a vented gas log set can be used as long as the damper is removed from the unit, but any other type of unvented log set will cause hazardous conditions.

Not directly. We only sell fireplaces through our local dealers. You can find a dealer near you by clicking on the Dealer Locator tab and entering your zip code, state or province in the box provided.

In an effort to deliver quality products, service, and safety, Hearth & Home Technologies, Inc. distributes our family of products exclusively through authorized and trained distributors and dealers. Occasionally, individuals will attempt to sell products online without the consent of the manufacturer. Heatilator, Heat & Glo, Harman and Quadra-Fire do not authorize the sale of products online. Here are a few things to consider if you are contemplating an online purchase of a quality hearth product.

Warranty - Heatilator, Heat & Glo or Quadra-Fire does not warranty products sold outside of our authorized dealer network, nor will they warranty service work on the product that is performed by anyone other than an authorized dealer. In addition, the warranty on our products applies to the original owner only and is nontransferable.

Customer Expectations - Our dealers are trained to evaluate your specific needs and suggest to you the products that will best meet those needs. When buying products online, you may be purchasing products that are not ideal for your situation and, as a result, be more costly than you anticipated. The products also require specific venting components with restrictions as to their installation which may not be evident in the purchase without a trained dealer to assess the installation application and recommend the appropriate venting scheme.

Shipping Damage - Our products are designed to ship to our customers using approved carriers and processes. The risk for damage increases if you attempt to ship product outside of our dealer network. We will not be responsible for any costs related to shipping damage.

Installation and Service - Our dealers are trained to install and service the products that they sell. We strongly recommend our products be installed and serviced by authorized dealers. Your warranty will be void if the product is not installed, operated and maintained in compliance with local building codes and with the instructions in the installer’s guide, owner’s guide and listing agent identification label furnished with the product. Your warranty will also be void if any service work is performed on the product by anyone other than an authorized representative. Furthermore, many local dealers will not service a fireplace they did not sell, making the authorized service of your product much more expensive. Lastly, the installation and set up of a product requires very specific installation and operational accessories. These accessories are often times not included in online sales, and can be very difficult and expensive to find after the fact.

For proper sales and service, find a local authorized dealer near you.

In many cases a gas fireplace has several facing and trim options. Fireplaces can be given a "face lift" by changing the stone facing or surrounds, and wood mantel options. Your local dealer can give you more details on the options for your particular fireplace, or visit our Fireside Furnishings website: www.firesidefurnishings.com.

No. The louvers allow room air to move around the heat exchanger. Blocking this air flow can cause fires and will void your manufacturer's warranty and possibly your homeowner's warranty.

Yes! However, there is an operational priority (Pecking order) of the various ways to turn your fireplace ON or OFF. The highest priority goes to the ON/OFF switch located near the valve assembly. For example, if you have the fireplace is turned “ON” via this switch, it will negate the wall switch and ON/OFF feature of your remote control.

Next, the wall switch takes priority over the remote control. In other words, if the wall switch is in the “ON” position and the units switch is in the “OFF” position, the remote control will not be able to turn the fireplace on or off. In either case, the RCT-MLT functions will work unless the "on- off" feature of the wall switch or fireplace switch is in the “ON” position.

Many of our gas fireplace models that have louvers or grills on the front can have a fan kit added. You will want to make sure that electricity is run to the junction box underneath the fireplace first, before ordering & installing a fan kit. You can test the junction box by plugging a lamp into the junction box and switching it on and off. Also make sure the circuit breaker is not tripped. If there is no electricity to the junction box you would have to run electric to the fireplace first before the fan kit could be installed. You can order a fan kit through your local dealer; installation instructions are packed with it.

Installation of our hearth products must be done in strict accordance with local or national building codes, and the unit's installation manual. We recommend that our products be installed by a factory-trained professional. You can find a factory-trained professional on this website under the Dealer Locator section.

You need to check with the manufacturer of your television. We follow the recommendations of the TV manufacturer. NOTE: we take no responsibility of any damage caused by the heat of the fireplace.

No. We make a wide variety of products that can be used in an outdoor porch, patio or open area under the Outdoor Lifestyles product line. You can view these products on this website under Outdoor Products.

No. The damper must be in the fully open position when using a wood-burning fireplace. Partially closing the flue (chimney) damper can cause smoke to spill into the room when burning wood, or cause carbon monoxide (CO) to come into the room when using gas logs.

Not on a direct vent or B vent model. A gas fireplace is an engineered system that includes the firebox, burner, logs, venting and options which are tested and listed by AGA or UL. Changing any of the specifications or placement of the logs could void your manufacturer's warranty, and possibly even your homeowner's warranty.

Not if your fireplace was shipped with a glass panel on the front. Direct vent fireplaces are sealed combustion systems and need the glass on to function properly. We sell optional screen mesh panels that go on the front of the glass that takes away any reflection, and adds an additional safety barrier against accidental contact with the hot glass panel. The other type of gas fireplaces we sell, called B-vent fireplaces, come with fixed, not sealed, glass fronts. You would need to check with your local dealer in the area to determine if the glass panel can be removed from this type of unit. Because removal of the glass is totally dependent on the specific unit installed, we cannot recommend that the glass be removed unless the specific model of unit denotes that it can be removed and the fireplace will still operate safely.

It's not recommended in climates that are high in humidity. Otherwise, you can turn the pilot off when you won’t be using your appliance for an extended period of time, and then use our on-line instructions to relight the pilot when needed.

No. The frequency of the remote control cannot be changed without special equipment, which is not readily available to homeowners and/or service companies. Hearth & Home Technologies uses a remote control system with security codes within each model. These security codes are burned into the transmitter of each model and cannot be changed. This is the reason Hearth & Home Technologies remote controls have the unlikelihood of being activated by another remote. If there is more than one Hearth & Home Technologies remote control at a home it is important that each hand-held transmitter has had the “learn” function activated to its designated receiver. If one hand-held transmitter was used in the “learn” activation for both receivers only one hand-held will function.

No. The Manufacturer’s Suggested Retail Price (MSRP) shown on the website includes the fireplace or appliance only. Fronts, piping, surrounds, gas or electric connections, and installation will be in addition to this suggested price.

Hearth & Home Technologies remote controls have a manual switch on the receiver that can be turned to the OFF position. This switch is manual and will break the contact with the power source, whether it is battery or 120V power. This switch is just like the main power switch that controls any electrical appliance. It is completely unnecessary to unplug or remove batteries from the receiver.

Taking the batteries out of the hand held transmitter will not guarantee against accidental activation. Remember that each remote is equipped with a safety feature, which turns the fireplace off after 9 hours of continuous usage, when operated in the “manual mode”.

Operating the fireplace for longer than a continuous 9 hours is not a safety issue, but can cause the temperature in the room of the fireplace to reach higher than normal temperatures. It is always required to maintain the necessary clearance to combustibles as prescribed in the fireplace installation instructions.

On new wood-burning fireplaces, first determine what you are burning. You should only be using seasoned wood, newspaper, or kindling. Firestarters can cause a smell. Seasoned fireplaces: what have you burned in the past? Have you cleaned the fireplace prior to burning? If you have used firestarters and/or prefabricated logs, these products are bound together with a wax-type substance, which does not dissipate. This wax can pool and has been found under the hearth refractory and can cause a very foul odor. Also check what is on top of the fireplace. Remove all objects from mantel to see if this eliminates the smell.

Each fireplace has a rating plate either inside the operating door or in the lower controls cavity. On that rating plate is your model number and serial number. Wood-burning fireplaces have a metal serial/model plate in the upper left side or right side of the firebox, or riveted on the smoke shield behind the screen. Gas burning fireplaces and inserts have a serial/model/rating plate in the lower cavity controls area. Gas stoves have a serial/model/rating plate attached to the back of the stove or inside the pedestal base.

Hearth & Home Technologies’ remote controls work by radio frequency, which offers the unlikelihood of another remote control activating your individual gas fireplace product.

Infrared (light signals) is often used with television and stereo remotes and requires there be no interference between the hand-held and the receiver. Fireplace facings, louvers and different installation options make infrared an unreliable option for fireplaces. Also, the brightness of the flame interferes with infrared control systems.

Sonic or Sound is the third technology used with remote controls. The early sonic technology was used on television, but quickly abandoned due to limitation in channels and choices. Most Sonic technology is used in the pest control industry today.

The Quadra-Fire wood stoves incorporate secondary burn tubes, which are more efficient, burn cleaner and require less maintenance than stoves with catalytic converters. More than 50% of the heat from your wood stove comes from burning the smoke, and stoves with secondary burn tubes burn that smoke inside the firebox, instead of in your chimney. Generally, the Quadra-Fire wood stoves average fewer emissions versus the EPA standard of 6 grams per hour. They are very clean burning. And, over the life of a catalytic converter stove, you will need to replace the converter several times. This is quite a costly maintenance requirement. You will not need to replace the heat tubes on the Quadra-Fire stoves.

The majority of our gas fireplaces and inserts are direct vent (DV). This means they have a fixed glass front which seals the gas burner and combustion firebox off from your home. 100% of the combustion air used by the fireplace comes from outside the home through a coaxial pipe. A smaller pipe inside the larger pipe eliminates all combustible gases, maintaining indoor air quality. The vent can be run horizontally through an outside wall, or vertically through the roof, depending on your preference.

It is very important to clean your glass after the initial 3 hours of burn time. Failure to do so can cause permanent etching of your glass.

  1. Make sure your glass is completely cooled. It is also recommended to turn the gas off when servicing your appliance.
  2. Remove the front face or louvers of your fireplace; carefully remove the glass assembly of your fireplace (following the instructions in your manual) and lay it on a soft surface.
  3. Wipe both sides with household glass cleaner (do not use a product with ammonia), using a soft cloth.
  4. For heavy deposits, use Stove Bright Glass Cleaner , Rutland White Off Glass Cleaner, or other hard water deposit glass cleaner recommended by your servicing dealer.
  5. Carefully replace glass on front of fireplace (following the instructions in your manual), making sure glass assembly and front are secured.
  6. After this initial cleaning, clean your glass as often as necessary, particularly if adding new ember material. Never use any abrasive cleaners or cloths to clean your glass. Scratching can cause the glass to shatter.

CAUTION: ALWAYS REMOVE YOUR FIREPLACE GLASS PRIOR TO LIGHTING YOUR PILOT

STEP 1: Locate gas supply valve (typically behind louvers, below glass opening - may be red or blue).

STEP 2: Open valve by pivoting handle to be parallel to gas line.

STEP 3: Locate pilot assembly with spark igniter (located behind and below logs in the firebox - typically in the bottom center).

STEP 4: Then locate red or black igniter button.* Push igniter to verify spark at pilot area.

STEP 5: Locate the black or green valve control knob (knob with the words "ON", "OFF" and "PILOT" on it). Push in and rotate counter-clockwise until the word "pilot" is in the 6 o'clock position.**

STEP 6: While pressing and holding in the valve knob (in "PILOT" position - it should press in about 1/4"), press the red piezo button repeatedly (once per second) until the pilot ignites. If the pilot does not light, wait 5 minutes and try again. Once the pilot is lit, continue to hold the valve knob in for 30 seconds, then slowly release.

STEP 7: If the pilot light goes out, contact your nearest dealer for service. Remember to shut the gas supply valve off (picture #1). If it remains lit, press the valve knob in slightly and rotate counter-clockwise until the word "ON" is in the 6 o'clock position.

STEP 8: Finally, turn the unit's ON/OFF switch (or wall switch or remote control) to the "ON" position to start your fire. Make sure you put the glass front back on the fireplace prior to burning your fireplace. Make sure the glass is securely clamped on, at all points, prior to replacing the front.

STEP 9: Enjoy your fireplace!

* If you do not see a red or black spark igniter button, you do not have a manual ignition system. If power is actively supplied to your fireplace, simply turn the on/off button, wall switch or remote control to "on" to ignite your main burner.

** Note: Some valve assemblies may be inverted in their brackets. If yours appears to be the mirror image of picture #4, then the word "PILOT" will be in the 12 o'clock position to light the pilot, and "ON" will be set to the 12 o'clock position to turn on your main burner.

CAUTION: ALWAYS REMOVE YOUR FIREPLACE GLASS PRIOR TO LIGHTING YOUR PILOT

Please refer to the installation manual or users guide for your fireplace to see how the glass is attached to your specific model and instructions for removal.

The FCC in the United States and IC in Canada regulate the distance in which a radio frequency from the hand-held transmitter can operate. In optimum conditions, this distance is 90 feet. Since there are many things than interfere with radio frequency the maximum realistic distance from which a hand-held transmitter will communicate with the receiver is 25 feet. Radio frequency will go through normal residential constructed walls (wood, plaster, drywall), but distance will be reduced traveling through walls.

Under normal operating conditions the batteries should last 6 – 12 months. Each of the batteries used in the hand-held transmitters should be producing 1.5V to 1.6V to operate. If the batteries are generating 1.3V to 1.35V or less the batteries should be replaced and can cause intermittent operation.

Your fan kit has a rheostat control (like a light dimmer). You can get more air from your fan by making sure the fan control is turned up to the desired level. The fan control can be found in the control area behind the lower louver of the fireplace, or on a wall switch with rheostat. We also provide optional remote controls which can control your fan speed from your favorite chair! Your dealer can help you with adding a remote control.

Our fans are purposely designed at lower CFMs (cubic feet per minute). There are two reasons for this. This first is to minimize fan noise. Second, a high velocity would tend to cool the air temperature coming out of the top louver of the fireplace. The fan is designed to move warm air into the room, not to move air clear across the room.

On gas fireplaces that are not brand new and are emitting some odor, try cleaning behind the upper and lower louvers. Dust can cause odor. Another source of odor can be the items you have on your mantel. Remove all objects from your mantel and then replace the objects one at a time. A third source of odor can be from the adhesives used in surround materials. This will need to be investigated by your installer. If these suggested sources don’t correctly identify the odor, contact your dealer where the fireplace was purchased and have your fireplace inspected.

No, absolutely not. A direct vent uses a high temperature glass panel to seal off the burn area of the fireplace from the interior of the home. It pulls 100% combustion air to feed the fire from outside the home. Because of its design, a direct vent gas fireplace will not affect the indoor air quality of your home. Since no air from your home is going up the chimney, a direct vent model is very efficient. Vent free should actually be called room vented since the by-products of gas combustion all spill back into the room. The single largest by-product of the gas combustion process is water vapor. Over sizing or overuse of a vent free hearth product can lead to excess moisture in a well built, tightly constructed home. Excess moisture inside the home can contribute to odors, mold and mildew inside the home.

Our fan kits come with a rheostat control (like a light dimmer). You can turn the control down to reduce the air noise from your fan. The fan control can be found in the control area behind the lower louver of the fireplace. We also provide optional remote controls which can control your fan speed and flame height from your favorite chair! Your dealer can help you with adding a remote control.

The following are the top reasons why remotes do not function:

1) Batteries do not have enough power or are installed incorrectly.
2) Misunderstanding on how the remote features operate the fireplace.
3) The slide switch on the receiver is not in the correct position.
4) The remote hand-held transmitter has not had the “learn” function activated to the receiver.
5) For standing pilot units, the thermopile must generate a minimum of 200 Millivolts. The fireplace requires more millivolts to operate via the remote control because it adds resistance to the system.
6) Defective component, for which replacement parts can be purchased or replaced under warranty within 1 year of the purchase of the remote.

1) The on/off switch on the fireplace and/or wall may be in the on position. This will over ride the remote control feature.
2) The remote is in the thermostat mode (SMART-STAT and RCT-MLT models) and the temperature of the room has not exceeded the desired temperature setting by 2 degrees Fahrenheit or 1 degree Celsius.
3) Batteries in the hand-held transmitter are old and underpowered. May work up close and will not work a few feet away.
4) Hand-held transmitter is outside of the 25’ of operation.
5) Hand-held transmitter has been dropped and the frequency has been moved off the frequency of the receiver.

Yes. We recommend annual service of your fireplace by a qualified serviceperson. This will ensure that your appliance is functioning properly.

If your system is controlled from an IntelliSwitch wall control, the batteries may be left in the unit. If not, install the batteries only when there is a power outage.

When the remote is in the thermostat mode (SMART-STAT and RCT-MLT models) and the temperature of the room has not exceeded the desired temperature setting by 2 degrees Fahrenheit or 1 degree Celsius the fireplace will not turn on and off. The thermostat is set with a 2 degree F (1 degree C) range to avoid continuous cycling of the fireplace.

The glass on a gas fireplace WILL reach very high temperatures. USE CAUTION: Carefully SUPERVISE children in the same room as your appliance; alert everyone to the hazards of high temperatures; do NOT operate with protective barriers removed; keep clothing, furniture, draperies and other combustibles away. Barriers such as screens over our direct vent glass help reduce the risk of burn from touching the glass. These screens are available through your local dealer.

While direct vent gas fireplaces are designed principally for their aesthetic value, we try to get as much heat output as possible to provide added value to the homeowner. It should be noted that while we are getting a lot of heat, we are passing the ANSI and UL standards for combustible temperatures. The allowable is 117°F above room temperature for combustibles. Average room temperature is 70-75°F; therefore a 187-192°F surface temperature can be expected. On a solid surface, 150°F is very hot to the touch (to put this in perspective, water boils at 212°F and the average bath water temperature is 110°F).

Each system is calibrated by the manufacturer and may not match exactly. If the temperature readings are within 3 degrees this is within the specification.

The temperature from one device to another is difficult to determine. The location of the thermostat is very important to the temperature that you are reading at any point in time. The important thing to remember is that you should develop a comfort area and the appliance will keep you at your comfort level rather than the exact temperature read out.

1) A hand-held transmitter. This is like a TV remote with which a person operates various features of the fireplace.
2) A receiver. This is located inside or near the fireplace and receives the radio frequency from the hand-held transmitter.
3) A Solenoid (for remote model RCT-MLT). This provides the option of a remote controlled variable flame. The solenoid is installed onto the regulator (located on the gas valve) of the fireplace to vary the gas pressure to the burner.

Excessive metal will deflect radio frequency in a direction that may not be in line with the receiver of your remote control. Interference of your radio frequency can cause the remote control to not respond properly to the hand-held transmitter. Hearth & Home Technologies has many built in safety functions to ensure that your remote control and fireplace operate in harmony. For this reason the receiver of the remote should not be installed to the very back of the fireplace. Large metal artwork can interfere with radio frequency.

Intermittent Pilot Ignition is an electronic system, which uses an electrode to ignite the pilot gas. In turn, the pilot flame lights the main burner gas. The term Intermittent is used because the pilot burner flame is only present when the main burner is operating. When the main burner is off the pilot is also off. The IPI system ensures the pilot flame extends over the burner for immediate ignition and secondly conserves energy when the appliance is not in operation.
Intellifire, an ignition system exclusively featured in Heatilator, Heat & Glo & Quadra-Fire products, is an energy-saving pilot ignition system for gas fireplaces and inserts. It provides an ignition flame only when needed and has a battery backup system that supplies power to spark the ignition flame in the event of a power outage.

Both the transmitter and receiver in model SMART-BATT are powered by batteries. Models SMART-STAT, RCT-MLT, RC-100, RC-200, and RC-300 are powered by batteries in the hand-held transmitters. The receiver is plugged into the junction box located in the bottom of the fireplace (Note: this requires an electrical hookup by qualified electrician at time of fireplace installation).

Hearth & Home Technologies offers several remote options with different features and functions to fit the different needs of today homeowners. They are all compact in size to fit the palm of your hand and come with a wall mounting bracket for easy storage.

SMART-BATT - This remote is perfect for you if your fireplace was previous installed without power and it would be too costly or impossible to wire electricity to it. This remote offers the feature of turning the flame on and off manually or by thermostatic temperature control. Count down timer system (15 min to 9 hours). 24 hour clock. Low battery indicator icon. Safety Feature: child proof setting to disable the on/off button and manual shutdown after 9 hours of continuous operation.

SMART-STAT –120 volts must be wired to the fireplace. This remote is ideal for the homeowner who wants the functions of a wall thermostat and the convenience of a remote control. Use manual or thermostatic settings to operate the fireplace at desired temperature between 45 to 99 degrees. Count down timer system (15 min to 9 hours). 24 hour clock. Low battery indicator icon. Safety Features: A child proof setting to disable the on/off button is also standard and manual shutdown after 9 hours of continuous operation.

RCT-MLT – If you enjoy having the best, then this remote is ideally suited for you. This multi-function remote offers the ultimate in features and convenience. It can conveniently do the following with just the touch of a button:
- Turns the flame on and off manually.
- Functions as a remote thermostat.
- Has an automatic timer function that allows you to turn the fireplace on for a desired amount of time between 1 to 90 minutes.
- Easily adjusts your fan setting (High, Medium, Low).
- An LED/LCD digital read out of the room’s temperature.
- Safety features; If the fireplace is turned on manually or by the thermostat and is on constantly for 9 hours the remote will turn the fireplace off.
- Child Proof setting to disable the on/off button is also standard.

Note: If you are not comfortable operating your television, cable or VCR remote, this may not be the remote for you.

There are several possible causes of feeling cold air from a wood fireplace. You will want to make sure the damper is closed. Also check the installation manual for any other potential openings that may need to be shut. If the fireplace is mounted on cement versus plywood, that can also transfer cold into your home. If the chase area or doghouse is not insulated adequately, that is another possibility. Please check with your builder or installer on the insulation of the chase.

This is normal in the first few minutes of operation. If after the first 30 minutes of full burn you still have blue flames, an adjustment may be needed on your unit. For assistance with this, contact your dealer.

Sooting is a result of impingement caused by incomplete combustion, i.e. flames coming in contact with a surface, cooling the flame, and preventing combustion.

Remote Controls are a consumer convenience. They are great for the busy lifestyles of today and will enhance the relaxing mood created by our gas fireplace by allowing the user to relax in their favorite chair and operate their fireplace while reclining in comfort. They are especially convenient in large rooms where a switch on the fireplace or on the wall is not always easily accessed. It is also an extremely popular option for bed/bath sitting rooms.

Most fans are wired into the fireplace with a fan sensor switch. This switch will activate the blower when the firebox heats up to a certain temperature. It will also automatically turn the blower off when the fireplace is turned off and the unit cools to a certain temperature. This sensor is provided so that you will not be circulating cold air in your home. The amount of time needed to heat up the fan sensor will differ depending on the model of your fireplace. It is common that blowers installed in Firebrick products will take longer to sense the heat and turn on your blower. Firebrick has greater insulating characteristics and holds the heat inside your firebox resulting in higher radiant heat and greater efficiencies

If your model has a standing pilot light, it does not require house current at any time to operate; or if your appliance has our patented IPI or IPI+ System, which works on a battery back up of 2 "D" or 4 "AA" batteries (depending on the particular ignition system), it will work in event of a power outage. You will need to install batteries for operation. If you have a fan or a remote control option, they will not work without power, but the appliance itself will burn and provide heat. (If you have a remote control, you may need to operate the appliance with the ON/Off switch in the control area of the appliance).

A damper clamp will come standard with your gas log set and MUST be installed to maintain a small opening at all times. This allows for the escape of any pilot exhaust. When the logs are in use the damper must be fully open.

Sign up to get your personalized coupon for $100 off a Heatilator fireplace, stove or insert. Offer expires 2/5/2017.

Get Coupon

Sign up to Save $100